Ingecon SUN 125 TL U 208 Outdoor Installation Manual Download Page 19

Page: 19 / 88

ABB2000IKI01

Installation manual

Ingeteam

2.1.8. Environmental characteristics

The environmental conditions for operation are:

Ambient conditions

Minimum temperature

(1)

-4 °F (-20 °C)

Minimum surrounding air temperature

(1)

-4 °F (-20 °C)

Minimum surrounding air temperature

149 °F (65 °C)

Temperature at which power limiting commences

122 °F (50 °C)

Maximum relative humidity without condensation

95%

(1)

Units including a heating element kit may be installed in locations with a minimum temperature of -13 °F (-25 °C).

For further information see Chapter

“2.4. Location of the components”

2.2. Characteristics of the electrical installation

These units are designed to be connected to the low voltage public grid.

2.3. EMC requirements

These units are equipped with the necessary filtering elements to comply with EMC requirements for industrial appli-
cations in order to prevent disturbances in other equipment outside the installation.

2.4. Location of the components

See next pages.

Summary of Contents for SUN 125 TL U 208 Outdoor

























































































Search results

Summary of Contents for SUN 125 TL U 208 Outdoor

Reviews:

Ingecon SUN 125 TL U 208 Outdoor, Installation Manual, Page: 19 / 88

Search results

Summary of Contents for SUN 125 TL U 208 Outdoor

Reviews: