manualshive.com logo in svg

Ingecon SUN 125 TL U 208 Outdoor, Installation Manual, Page: 68 / 88

Share
Download
Ingecon SUN 125 TL U 208 Outdoor Installation Manual Download Page 68

ABB2000IKI01

68

Installation manual

Ingeteam

Screen 5

Rpv

Impedance of the entire PV array to ground.

Rpv+

Impedance of the positive pole of the PV array to ground.

Rpv-

Impedance of the negative pole of the PV array to ground.

Screen 6

Alarms

Status of inverter alarms.

0000H

No alarms.

0001H

Grid frequency out of range.

0002H

Grid voltage out of range.

0004H

PI current  saturation.

0008H

Unexpected reset.

0010H

Continuous overload at output.

0020H

Temperature alarm in the power electronics.

0040H

Hardware fault. Synchronization fault.

0080H

Instantaneous overload at output.

0100H

AC circuit protection.

0200H

DC circuit protection.

0400H

Insulation fault.

0800H

Power electronics fault.

1000H

Manual shutdown alarm.

2000H

Configuration change alarm.

4000H

Panel input overvoltage.

8000H

Low voltage in the PV array.

Alarmas Hist

Alarms since the last connection. This value is reset each time the inverter is connected to the grid. It 
has the same code as the “alarms” variable.

TempInt

Inverter power electronics temperature.

TempCI

Inverter control electronics temperature.

Screen 7

Conn.N

Number of grid connections made during all hours of operation.

ParConn.N

Number of grid connections since counter was last reset.

ConnT

Number of hours the inverter has been connected to the grid.

Par.ConnT

Number of hours the inverter has been connected to the grid since the counter was last 
reset.

8.5.  Reasons for shutdown

This menu shows the last five inverter shutdowns, with reasons and corresponding date and time.

17:05

24/06/12

17:05

24/06/12

Meaning of reasons for shutdown:

Summary of Contents for SUN 125 TL U 208 Outdoor

























































































Reviews:

No comments