manualshive.com logo in svg

Ingecon SUN 125 TL U 208 Outdoor, Installation Manual, Page: 65 / 88

Share
Download
Ingecon SUN 125 TL U 208 Outdoor Installation Manual Download Page 65

ABB2000IKI01

65

Installation manual

Ingeteam

8.  Display control

These inverters incorporate a display and keypad unit to interface with the 
installer and the user.

This interface allows the display of the main internal parameters and the configu-
ration of the entire system during installation.

Parameters, variables and commands are organized as menus and submenus.

8.1.  Keypad and LEDs

The keypad has four keys:

Esc.

 To exit a parameter, leave a menu and returning to the next level up in the structure, to not 

confirm a change or not accept a suggestion.

Up.

 With this key you can scroll up the list of parameters or folders within the same level or 

increase the value of an editable parameter by one base unit.

Down.

 With this key you can scroll down the list of parameters or folders within the same level or 

decrease the value of an editable parameter by one base unit.

OK.

 Serves to accept a parameter as valid, to enter a lower level menu in the structure, to confirm 

a change or accept a suggestion.

The front panel has three LEDs:

Green LED

• 

Slow flashing: Standby due to low irradiance.

• 

Fast flashing: Start-up process.

• 

On: Inverter connected to the grid.

Orange LED

Fast flashing: Alarm set off which does not shut down the inverter.

Red LED

 

On: Alarm set off which shuts down the inverter.

 

Special combinations

Rapid flashing of all three LEDs: Fatal error status.

Summary of Contents for SUN 125 TL U 208 Outdoor

























































































Reviews:

No comments