manualshive.com logo in svg

Ingecon SUN 125 TL U 208 Outdoor, Installation Manual, Page: 70 / 88

Share
Download
Ingecon SUN 125 TL U 208 Outdoor Installation Manual Download Page 70

ABB2000IKI01

70

Installation manual

Ingeteam

17:05

24/06/12

English

17:05

24/06/12

English

Press the 

 button to scroll through the various languages and 

 to confirm the selection.

Grid quality

In this menu, you can change the grid quality parameters. This menu is only active after the security code has been 
input.

Ground connection

Through this option, you can change the type of grounding for the PV array. This menu is only active after the security 
code has been input.

Connection time

This menu allows you to modify the delay before the inverter connects to the grid. This menu is only active after the 
security code has been input.

Total reset

With this option, the user can reset all inverter counters. This menu is only active after the security code has been 
input.

Other adjustments

Various internal adjustments.

Change NumCAN

From this menu you can change the node number. This is useful for units with more than one electronics block, and 
should not be changed on the unit unless so instructed by Ingeteam.

8.7.  Inverter data

This window displays inverter-specific data:

17:05

24/06/12

17:05

24/06/12

Serial Number (NS)

Number that identifies the inverter.

Firmware Version (Firm)

Shows the name and version of the inverter firmware.

Display firmware version (FirmDis)

Shows the name and version of the inverter display.

Boot version of the display (BootDis)

Shows the name and version of the display Boot.

Summary of Contents for SUN 125 TL U 208 Outdoor

























































































Reviews:

No comments