Infinity 6250LQ Operation Manual Download Page 7 | Manualshive

Page: 7 / 44

background image

FY operation manual

- 7 -

Chapter 3

EQUIPMENT ASSEMBLY AND ADJUSTMENT

3.1 Assemble Digital Printer

Figure 3-1 Packing screw’s detachment

Figure 3-2 Screw installation and print head fixation screw detachment

1.

According to the Pattern above, please assemble kickstand by following step: feet with truckle,
kickstand, and ink supply box.

2.

Please tighten all Screws on the Feet; prepare to assemble the Core Part.

3.

Please confirm carrying on assemble project with sufficient workmates, and then tighten all screws
with core part. Confirm no shaking occurs.

4.

Install ink supply system on right side.

5.

Please connect all data wire and power wire correctly.

3.2 Adjust Digital Printer

1.

Make sure all data wire and power wire connected correct, and then Turn on your Printer.

2.

Put media on the roll behind the Printer or insert single sheet paper on the printing table. Clamp the
pole on the right of Printer. The Printer detects the media width automatically.

Screw
detachment

Screw
detachment

Print head fixation
screw detachment

Screw
installation

Screw
installation

Ink tank

«
...
5
6
7
8
9
...
»

Summary of Contents for 6250LQ













































Reviews:

No comments

Related manuals for 6250LQ

Brand: Oki Pages: 2

Magicolor 2 plus

Brand: QMS Pages: 90

Magicolor 2 Desklaser

Brand: QMS Pages: 4

Brand: QMS Pages: 8

Brand: QMS Pages: 94

Brand: QMS Pages: 6

Brand: Duplo Pages: 123

Brand: Make Mendel Pages: 29

Brand: Xerox Pages: 78

Brand: Konica Minolta Pages: 4

Brand: Gestetner Pages: 4

Aficio SP 320 Series

Brand: Ricoh Pages: 272

Brand: Ricoh Pages: 84

Brand: Printronix Pages: 148

4039 - B/W Laser Printer

Brand: Lexmark Pages: 49

Brand: Lexmark Pages: 64

Brand: FARGO electronics Pages: 228

Brand: FARGO electronics Pages: 220

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands