manualshive.com logo in svg

Infineon Technologies TLE5012B, User Manual, Page: 6 / 105

Share
Download
Infineon Technologies TLE5012B User Manual Download Page 6

TLE5012B

List of Figures

  

User’s Manual

6

Rev. 1.2, 2018-02

   

Figure 1-1

PG-DSO-8 package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  9

Figure 1-2

A usual application for TLE5012B is the electrically commutated motor  . . . . . . . . . . . . . . . . . . . .  10

Figure 2-1

TLE5012B block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  11

Figure 2-2

Laser Fuses burning process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  12

Figure 2-3

PRO-SIL

TM

 Logo. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  13

Figure 2-4

Sensitive bridges of the GMR sensor (not to scale) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  14

Figure 2-5

Ideal output of the GMR sensor bridges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  15

Figure 2-6

Pin configuration (top view)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  16

Figure 3-1

Application circuit for TLE5012B with IIF interface and SSC . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  17

Figure 3-2

Application circuit for TLE5012B with HSM interface (push-pull configuration) and SSC  . . . . . . .  17

Figure 3-3

Application circuit for TLE5012B with HSM interface (open-drain configuration) and SSC . . . . . .  18

Figure 3-4

Application circuit for TLE5012B with PWM (push-pull configuration) interface . . . . . . . . . . . . . . .  18

Figure 3-5

Application circuit for TLE5012B with PWM (open-drain configuration) interface  . . . . . . . . . . . . .  19

Figure 3-6

Application circuit for TLE5012B with SPC interface  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  19

Figure 3-7

SSC interface with push-pull configuration (high-speed application) . . . . . . . . . . . . . . . . . . . . . . .  20

Figure 3-8

SSC interface with open-drain configuration (bus systems) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  20

Figure 3-9

Sensors’ supply in bus mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  21

Figure 4-1

Parameter correction with autocalibration mode 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  22

Figure 4-2

Parameter correction with autocalibration mode 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  22

Figure 4-3

Parameter correction with autocalibration mode 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  23

Figure 4-4

Cases where an angle error adder has to be included if autocalibration is enabled  . . . . . . . . . . .  25

Figure 4-5

Delay of sensor output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  26

Figure 4-6

Revolution counter with prediction mode disabled/enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  26

Figure 5-1

SSC timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  31

Figure 5-2

SSC data transfer (data-read example) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  33

Figure 5-3

SSC data transfer (data-write example) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  33

Figure 5-4

SSC bit ordering (read example)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  35

Figure 5-5

Update of update registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  35

Figure 5-6

Example of four slaves connected to a bus with one master with SSC interface . . . . . . . . . . . . . .  36

Figure 5-7

Fast CRC polynomial division circuit  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  37

Figure 5-8

TLE5012B’s CRC generator polynomial for the SSC interface  . . . . . . . . . . . . . . . . . . . . . . . . . . .  37

Figure 5-9

CRC generation example with SSC interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  38

Figure 5-10 Flow-Chart of Angle Calculation from the X-raw and Y-raw values . . . . . . . . . . . . . . . . . . . . . . . .  45
Figure 5-11 Typical example of a PWM signal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  46
Figure 5-12 Example of four slaves connected to a bus with one master with SPC interface . . . . . . . . . . . . . .  48
Figure 5-13 SPC frame example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  49
Figure 5-14 SPC pause timing diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  49
Figure 5-15 SPC configuration in open drain mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  49
Figure 5-16 SPC Master pulse timing  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  51
Figure 5-17 TLE5012B’s CRC generator polynomial for the SPC interface  . . . . . . . . . . . . . . . . . . . . . . . . . . .  52
Figure 5-18 CRC generation example with SPC interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  52
Figure 5-19 Hall Switch Mode  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  55
Figure 5-20 HS hysteresis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  58
Figure 5-21 Incremental interface with A/B mode  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  59
Figure 5-22 Incremental interface with Step/Direction mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  59
Figure 5-23 Increcremental Interface startup pulses and first step movements at different speeds . . . . . . . . .  60
Figure 5-24 Increcremental Interface startup pulses frequency. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  61
Figure 5-25 IIF Index pulse in A/B Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  61
Figure 5-26 IIF Index pulse in Step/Direction Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  62

List of Figures

Summary of Contents for TLE5012B










































































































Reviews:

No comments