Inficon 540-200 Translation Of The Original Operating Instructions Download Page 64

Page: 64 / 90

7 | Controlling the device using interfaces

INFICON

64 / 90

T-Guard2_Operating-instructions-jina85en1-13-(2009)

7.1.3 Acumulation measurement using PLC

► Start the measurement when READY is low resistance.

The MEASURE output is low resistance during the measurement.

After the measurement, the MEASURE output becomes high resistance. If only the

REC STROBE output is high resistance again, you can read out the analogue outputs.

This is the case after approx. 300 ms.

If automatic purging is activated, READY becomes low resistance after purging. Only

then can the next measurement be started.

Fig. 28: Example of a PLC- controlled accumulation measurement

Fig. 29: Example of a PLC- controlled accumulation measurement

Summary of Contents for 540-200



























































































Search results

Summary of Contents for 540-200

Reviews:

Related manuals for 540-200

Brands by name

Popular brands

Inficon 540-200, Translation Of The Original Operating Instructions

Search results

Summary of Contents for 540-200

Reviews:

Related manuals for 540-200

Brands by name

Popular brands