Inficon 540-200 Translation Of The Original Operating Instructions Download Page 30

Page: 30 / 90

5 | Installation

INFICON

30 / 90

T-Guard2_Operating-instructions-jina85en1-13-(2009)

5.3 Connecting an external control unit

NOTICE

Material damage due to connection error.

If you insert or remove the plug during operation, the device could be damaged.

► Only insert or remove the cable when the device is disconnected from the power

supply.

The diagram below displays the dimensions of the control unit for rack installation.

Fig. 11: Dimensions of the control unit for rack mounting

The front of the control unit for rack installation corresponds to protection class IP40.

• Place the table device on a stable base or mount the control unit in a rack.

• Connect the external control unit to the “CONTROL UNIT” connection on the T-

Guard2 using the corresponding cable.

• Secure the plug on the socket by tightening the screws.

Summary of Contents for 540-200



























































































Search results

Summary of Contents for 540-200

Reviews:

Related manuals for 540-200

Brands by name

Popular brands

Inficon 540-200, Translation Of The Original Operating Instructions

Search results

Summary of Contents for 540-200

Reviews:

Related manuals for 540-200

Brands by name

Popular brands