Inficon 540-200 Translation Of The Original Operating Instructions Download Page 65

Page: 65 / 90

INFICON

Controlling the device using interfaces | 7

T-Guard2_Operating-instructions-jina85en1-13-(2009)

65 / 90

7.1.4 Carrier gas measurement using PLC

The MEASURE output is low resistance during the measurement.

► Start the measurement when READY is low resistance.

After the measurement, the MEASURE output becomes high resistance. If only the

REC STROBE output is high resistance again, you can read out the analogue outputs.

This is the case after approx. 300 ms.

The READY output becomes low resistance after the reference measurement. This

lasts as long as the FINE measurement. The next measurement can only be started

after it.

Fig. 30: Example of a PLC- controlled carrier gas measurement

Fig. 31: Example of a PLC- controlled carrier gas calibration

Summary of Contents for 540-200



























































































Search results

Summary of Contents for 540-200

Reviews:

Related manuals for 540-200

Brands by name

Popular brands

Inficon 540-200, Translation Of The Original Operating Instructions

Search results

Summary of Contents for 540-200

Reviews:

Related manuals for 540-200

Brands by name

Popular brands