Inficon 540-200 Translation Of The Original Operating Instructions Download Page 55

Page: 55 / 90

INFICON

Operation | 6

T-Guard2_Operating-instructions-jina85en1-13-(2009)

55 / 90

6.7 Starting the measurement

Waiting time before the

start (only for carrier

gas measurement)

After closing the measurement chamber, wait for a defined amount of time, which is

calculated as follows:

Start

The measurement is started with the interface or with the selection of “Start”. During

the measurement, bars display the measurement progress. When the measurement is

finished, the display shows the leak rate or a malfunction message. The measurement

can be interrupted at any time by selecting “Stop”. The leak rate displayed at that point

is a provisional value.

Fig. 23: FINE measurement, progress bars

Fig. 24: Leak rate display of an accumulation measurement with information on the helium

background of the sensor and the surroundings.

Summary of Contents for 540-200



























































































Search results

Summary of Contents for 540-200

Reviews:

Related manuals for 540-200

Brands by name

Popular brands

Inficon 540-200, Translation Of The Original Operating Instructions

Search results

Summary of Contents for 540-200

Reviews:

Related manuals for 540-200

Brands by name

Popular brands