Inficon 540-200 Translation Of The Original Operating Instructions Download Page 76

Page: 76 / 90

10 | Warning and error messages

INFICON

76 / 90

T-Guard2_Operating-instructions-jina85en1-13-(2009)

E14

Discharge expired

Problem with sensitivity

at the Wise Technology

sensor

No helium in the

surroundings (e.g. inlet

openings purged with

nitrogen)

Restart the device but with

the inlet openings connected

to outside air.

If the problem persists,

contact the INFICON

customer service.

E20

Temperature at the

electronics unit too

high (>60°)

Ambient temperature

too high

Fan failed

Cool the surroundings, place

the device in a cooler room.

Check the fan (check the flow

rate through the inlet in the

housing)

W27

Incorrect

measurement

settings

The trigger setting is

smaller than 5 x the

minimum display

Correct the trigger value(s)

W28

Real-time clock was

reset! Enter date

and time

CPU card was replaced

CPU card battery is

faulty

Enter date and time

Contact INFICON customer

service.

E 38

Pump is faulty

Sensor pressure is

higher than 800 mbar.

Fore pump defective,

not switched on or

pump hose is broken.

Check the fore pump and the

lines to the device.

W41

Pressure difference

is too great

Pressure difference

between the

measurement inlet and

air inlet should be ±10%

Pressure difference

between READY and

FINE

Check the inlet filter.

W43

Pressure too low

Pressure below lower

limit

Reference line is

blocked

Check the upper pressure

limit

Check the reference line

W44

Pressure too high

Pressure above upper

limit

Bad fore pump

Pump hose is broken

Check the upper pressure

limit

Check the fore pump and the

pump hose

Summary of Contents for 540-200



























































































Search results

Summary of Contents for 540-200

Reviews:

Related manuals for 540-200

Brands by name

Popular brands

Inficon 540-200, Translation Of The Original Operating Instructions

Search results

Summary of Contents for 540-200

Reviews:

Related manuals for 540-200

Brands by name

Popular brands