Industrial Rivet & Fastener Co. RK-797 Series Manual Download Page 23 | Manualshive

Page: 23 / 32

background image

19

5.3

Approved Lubricants

The tool must not be cleaned with fat-solvent agents or water.

5.4

Removing the Nose Assembly



Remove the outer sleeve.



Remove the nose assembly



Disassemble and clean the nose assembly according to manufacturer

instructions.



Clean with mineral based cleaning agent and check wear off all components.



Replace as necessary and re-install in the reverse order

5.5

Cleaning the Jaws



Clean with mineral based cleaning agent and check wear off all components.

Warning!

The proper nose assembly must be selected for the lockbolt specified.
Contact your RivetKing® representative for assistance.

«
...
21
22
23
24
25
...
»

Summary of Contents for RK-797 Series

































Reviews:

No comments

Related manuals for RK-797 Series

Brand: Kelvin Pages: 2

Brand: RAMSET Pages: 16

Brand: Dafra Pages: 4

Brand: FAR Pages: 11

Brand: FAR Pages: 32

Brand: FAR Pages: 24

Brand: FAR Pages: 68

Brand: FAR Pages: 15

Brand: Gardena Pages: 7

Brand: Nederman Pages: 120

Brand: Huskie Tools Pages: 12

Brand: GOEBEL Pages: 23

Brand: YATO Pages: 88

Brand: Baileigh Pages: 39

Brand: PT Coupling Pages: 2

Brand: Ferm Pages: 58

Brand: Alice's Garden Pages: 26

Brand: Klein Tools Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands