background image

38

39

HOIST BRAKE SPARE PART LIST

PART NO.  PART CODE 

DESCRIPTION

 1 

XBAP0033PTA   

STUD

XBAP0032PTA   

LOCK NUT

XBAP0038PTA   

MOUNTING PLATE

XBAP0036PTA   

FRICTION DISC

XBAP0037PTA   

DUMMY PLATE

XBAP0034PTA   

RELEASE SPRING

XBAP003APTA   

SPRING COMP, NUT, & LOCK NUT

XBAP0830PTA   

GAP ADJU. NUT & LOCK NUT

11 

XBAP0026PTA   

COIL

12 

XBAP0730PTA 

RELEASE BOLT

HOIST BRAKE

SAFETY PRECAUTIONS

1.  To prevent electrical mishaps be sure to disconnect the power to the brake from its source 

before attempting to service or repair.

2.   Look down or secure any load hold by this brake prior to service or repair

3.   If this brake has been supplied with a manual hand release, do not override the brake by 

securing the hand release in an open position

4.   Do not operate brake in atmospheres with explosive gases and dusts or corrosive substances

  This brake can operate in non explosive dust or with optional seal in water splash and 

Almaden Atmospheres.

5.   When storing or installing the friction rotor, ensure that oil or grease is kept from the friction 

material surface.

Air gap Hand Release Value

Brake Size 

DAT 50X 

DAT 75X 

DAT 100X 

DAT 125X 

DAT 150X

Normal Air Gap mm 

0.50 

0.50 

0.50 

0.6 

0.3

Max Air Gap mm 

1.20 

1.20 

1.20 

1.2 

1.00

Hercules Hoists Limited ©2020

Note :- Due to continuous development and improvement specification listed above may be changed without notice

Indef CHAIN ELECTRIC HOIST

Hercules Hoists Limited ©2020

Note :- Due to continuous development and improvement specification listed above may be changed without notice

Indef CHAIN ELECTRIC HOIST

Summary of Contents for CH III
























Reviews: