background image

OPERATING INSTRUCTIONS 

CHAIN SLINGS GRADES 80 AND 100 

 

 

THIELE GmbH & Co. KG 

 

# Change indicator

 

www.thiele.de | [email protected] 

B11082-C 

replaces B11082-B

 

© All rights reserved. 

US 01.2020 

 1 | 11 

 

 

 

 

 

 

   

 

 

 

The following Operating Instructions must always be 

followed to avoid the risk of personal injury or property 

damage. 

Do not use a chain sling before reading these Operating 

Instructions. 

 

 

1.

 

ABOUT THIS INSTRUCTION 

This  Operating  Instruction  describes  in  particular  how  sling 
chains according to TWN 0805A grade 80, TWN 0072 and TWN 
1805 grade 100 (TWN = THIELE Shop Standard) are to be safely 
used for lifting purposes. 
The  instruction  applies  analogously  to  components  of  the 
identical design. 
To  comply  with  these  instructions  is  essential  to  help  avoid 
hazards and increases the reliability and service life of the chain 
slings. 
 

Chains and accessories marked with the American nominal size 
7/32

  already  corresponded  to  the  European  nominal  size           

6  mm.

 

In  order  to  achieve  a  better  match,  the  previous 

nominal size 7/32

 is now converted to the new nominal size 

15/64

. The working load limits have now also been adjusted.

 #

 

 

DEFINITIONS 

Clevis 

A U-shaped fitting with pin. 

Working Load Limit (WLL) 

The maximum load which a chain sling is designed to support in 
direct tension without shock loading at a designated sling angle 
of lift. 

 

 

Read ASME B30.9 ”Slings“, Chapters 9

-0 and 9-1. 

Read 

ASME B30.10 ”Hooks“.

 

Read ASME B30.26 “Rigging Hardware”,

                                                   

 

 

     Chapters 26-0, 26-1, 26-4. 

If chain slings are used with lifting magnets, read ASME 

B30.20 ”

Below-the Hook-Lifting-

Devices“, Chapter 20

-4. 

 

2.

 

BASIC SAFETY REQUIREMENTS 

 

 

To prevent the risk of injury never walk or stay under lifted 

loads! 

The Working Load Limit must not be exceeded! 

Only use lifting and attachment means free from defects! 

Working under the influence of drugs, medications 

impairing the sense and/or alcohol is strictly forbidden! 

 

 

 

 

Operators,  fitters  and  maintenance  personnel  must  in 
particular  observe  the  Operating  Instructions  as  well  as 
standards  ASTM  A  906/A  906  M  (Standard  Specification  for 
Grade  80  and  Grade  100  Alloy  Steel  Chain  Slings  for 
Overhead  Lifting),  ASTM  A  952/A  952  M  (Standard 
Specification for Forged Grade 80 and Grade 100 Steel Lifting 
Components and Welded Attachment Links), ISO 3056 (Non-
calibrated round steel link lifting chain and chain slings; Use 
and  maintenance),  ISO  7593  (Chain  slings  assembled  by 
methods  other  than  welding;  Grade  T(8))  and  ISO  4778 
(Round  steel  short  link  chains  for  lifting  purposes 

  Chains 

slings of welded construction 

 Grade 8). 

 

 

DANGER!

 Indicates a hazardous situation 

which, if not avoided, will result in death 
or serious injury. 

 

WARNING!

 

Indicates 

hazardous 

situation  which,  if  not  avoided,  could 
result in death or serious injury. 

 

CAUTION!

 

Indicates 

hazardous 

situation  which,  if  not  avoided,  could 
result in minor or moderate injury. 

 

NOTICE!

 Is used to address practices not 

related to physical injury. 

 

Safety Instructions

 signs indicate specific 

safety-related 

instructions 

or 

procedures. 

Summary of Contents for Grade 100












Reviews: