background image

4

5

CAUTION

Equipment described herein is not designed for and MUST NOT be used for lifting, supporting, 

or transporting people, or for lifting or supporting loads over people.

Equipment described herein should not be used in conjunction with other equipment unless 

necessary and/or required safety devices applicable to the system, crane, or application are 

installed by the system designer, system manufacturer, crane manufacturer, installer, or user.

Modifications to upgrade, rerate, or otherwise alter this equipment shall be authorized only 

by the original equipment manufacturer.

Failure to read and comply with any one of the limitations noted herein can result in serious 

bodily injury or death, and/or property damage.

The angle between rope and plane perpendicular to the axis of the drum shall not exceed 5° 

(As per IS 3938 6.1.1.2).

Hoists shall not be operated unless the hoist unit is centered over the load, except when 

authorized by a qualified person who has determined that the components of the hoist 

and its mounting will not be overstressed. Should it be necessary to pick a load that is not 

centered under the hoist unit, precautions should be taken to control the swing of the load 

when it is picked clear of its support.

DANGER

HAZARDOUS VOLTAGES ARE PRESENT IN THE CONTROL BOX, OTHER ELECTRICAL 

COMPONENTS, AND CONNECTIONS BETWEEN THESE COMPONENTS.

Before performing ANY mechanical or electrical maintenance on the equipment, de-energize 

(disconnect) the main switch supplying power to the equipment; and lock and tag the main 

switch in the de-energized position. 

Only trained and competent personnel should inspect and repair this equipment.

 Information

This symbol indicates tips and useful information.

Warning Tag and Labels

The warning tag illustrated below in Figure is supplied with each hoist and trolley shipped from 

the factory. If the tag is not attached to the pendant cord for your hoist/trolley, order a tag from 

your dealer and fixit it. Read and obey all warnings attached to this Hoist/Trolley. Tag is not shown 

in actual size.

WARNING

IMPROPER use of powered Hoist could result in death 

Or serious injury. 
To avoid these hazards:

 

ALWAYS read owner’s manual and safety 

instructions.

 

Do NOT lift more than rated load.

 

Do NOT lift or transport loads over or near people.

 

Do NOT use a hoist for lifting supporting or 

transporting people.

 

Do NOT operate unless load is centered under 

hoist.

 

Do NOT support a load on the tip of the hook 

 

Do NOT use a hoist if the hook latch is missing or 

broken.

 

Do NOT remove or obscure the warning lables.

 

Do NOT run the load chain or wire rope over a 

sharp edge.

 

Do NOT use the load chain or wire rope as a sling.

 

Do NOT operate beyond the travel limits of the 

hook or load block.

 

Do NOT use a twisted, kinked, damaged, or 

stretched load chain or wire rope.

 

Do NOT operate a wire rope hoist with a wire rope 

that is not properly seated in its groove.

Hercules Hoists Limited ©2020

Note :- Due to continuous development and improvement specification listed above may be changed without notice

Hercules Hoists Limited ©2020

Note :- Due to continuous development and improvement specification listed above may be changed without notice

Hercules Hoists Limited ©2020

Note :- Due to continuous development and improvement specification listed above may be changed without notice

Indef CHAIN ELECTRIC HOIST

Hercules Hoists Limited ©2020

Note :- Due to continuous development and improvement specification listed above may be changed without notice

Indef CHAIN ELECTRIC HOIST

Summary of Contents for CH III
























Reviews: