IMER 1106045 Operating, Maintenance, Spare Parts Manual Download Page 7

21

IMER INTERNATIONAL S.p.A.

IMER MORTAR MIXERS

11. START-UP (see fig.6)

After positioning the machine, prepare a bucket with a

quantity of approx. 10l. of grout. Pour the grout

into the

machine hopper, or, in the case of using colorant products,

directly in the machine pipelines before connection. In the

latter case, pour approx. 10l. of coloured product into the

hopper. Check the material hoses to ensure perfect

condition, that couplings are intact and the relative seals are

fitted, then connect them to the delivery manifold and spray

jet. Check that the cam levers ( A ) of the couplings have

been tightened correctly and that the seal (B) is fitted as

shown in fig. 6a.

Close the spray jet valve (ref. 15a), turn the main switch

(ref. 3) to 1(ON), switch on the optional compressor if used,

and turn the selector (ref. 7) clockwise to the start position.

The pushbuttons (+) flow rate (ref. 6) and (-) flow rate (ref.

5), control the flow rate as shown on the display (ref. 8) at

30. Open the spray jet air valve (or pneumatic control)(ref.

15d) or start the machine by means of the electric remote

control: the pump starts to rotate slowly. Depending on the

machine configuration, wait until the grout in the hopper

reaches the level of the mixer, or until the coloured product is

delivered from the jet. At this point shut down the machine by

means of the pneumatic or electric control, fill the hopper and

start work as required. Adjust the quantity of material

delivered from the jet as required, by means of pushbuttons

(+) and (-). When the electric remote control is connected,

the selector should be set to the start position. The machine

is controlled exclusively by means of the electric remote

control.

The machine is fitted with protection against power failure: if

this occurs, the main switch must be reset to restart the machine

(turn from 0 to 1).

To stop the machine in the event of an emergency, press the

red emergency button (ref. 2) To isolate the machine, all moving

parts are shut down and then turn the main switch to 0 and

remove the electric power plug from the socket (ref.11).

1

3

7

9

2

10

12

11

6

5

4

13

14

8

15a

15

15b

15c

15d

( A )

FIG.6b

( B )

FIG.6a

The machine must never be started up or remain in operation if

there is no material in the hopper, to avoid premature wear of the

stator and screw.

- Never direct the jet towards yourself or others

Summary of Contents for 1106045












Reviews: