IHP BarcelonaLights36ZEN Installation And Operation Instructions Manual Download

Page: 32 / 40

IHP.us.com

900861-00NC

Main Burner Orifice

(OAS-LP#)

Low Rate Set Screw

(ECO-LSS-#)

Figure 41 - Kit Contents

Gas conversion kits are available to adapt your appliance from the

use of one type of gas to the use of another. These kits contain all

the necessary components needed to complete the task including

labeling that must be affixed to ensure safe operation.

Kit part numbers are listed here and the following steps detail the

conversion procedure. Refer to the instructions provided with the

conversion kit when performing any gas conversion.

TOOLS / SUPPLIES NEEDED

Flat bladed screwdriver

Needle nose pliers

Pipe joint compound or teflon tape

Gas leak test solution

KIT CONTENTS

(1) OAS-LP# (brass orifice) and

(1) ECO-LSS# (brass low rate set screw),

(1) LP Conversion Label (placed next to blank space on rating label),

(1) Installation Instruction Sheet

CAUTION: THE GAS SUPPLY SHALL BE SHUT OFF PRIOR TO DIS-

CONNECTING THE ELECTRICAL POWER, BEFORE PROCEEDING

WITH THE CONVERSION.

ATTENTION: AVANT D’EFFECTUER LA CONVERSION,

COUPEZ D’ABORD L’ALIMENTATION EN GAZ, ENSUITE, COUPEZ

L’ALIMENTATION ÉLECTRIQUE.

READ ALL THE STEPS BEFORE STARTING THE CONVERSION. INSTALLER

NOTICE: THESE INSTRUCTIONS MUST BE LEFT WITH THE APPLIANCE.

When installing gas components use pipe joint compound or Teflon

tape on all pipe fittings before installing (Do not use pipe joint

compounds on flare fittings).

THE APPLIANCE MUST BE OFF AND COLD BEFORE PERFORMING

THE GAS CONVERSION.

ALL WARNINGS, PRECAUTIONS AND INSTRUCTIONS IN THE INSTAL-

LATION AND OPERATION MANUAL PROVIDED WITH THE APPLIANCE

APPLY TO THESE INSTRUCTIONS.

In Canada:

THE CONVERSION SHALL BE CARRIED OUT IN ACCORDANCE WITH

THE REQUIREMENTS OF THE PROVINCIAL AUTHORITIES HAVING

JURISDICTION AND IN ACCORDANCE WITH THE REQUIREMENTS

OF THE CAN/CGA-B149.1 INSTALLATION CODE.

LA CONVERSION DEVRA ÊTRE EFFECTUÉE CONFORMÉMENT AUX

RECOMMANDATIONS DES AUTORITÉS PROVINCIALES AYANT

JURIDICTION ET CONFORMÉMENT AUX EXIGENCES DU CODE

D’INSTALLATION CAN/CGA-B149.1.

WARNING

This conversion kit shall be installed by a qualified service

agency in accordance with the manufacturer’s instructions

and all applicable codes and requirements of the authority

having jurisdiction. If the information in these instruction

is not followed exactly, a fire, explosion or production of

carbon monoxide may result causing property damage,

personal injury or loss of life. The qualified service agency

is responsible for the proper installation of this kit. The

installation is not proper and complete until the opera-

tion of the converted appliance is checked as specified

in the manufacturer’s instructions supplied with the kit.

The qualified service agency performing this installation

assumes responsibility for this conversion.

AVERTISSEMENT

Cette trousse de conversion doit être installée par un

technicien agréé, selon les instructions du fabricant et

selon toutes les exigences et tous les codes pertinents

de l’autorité compétente. Assurez-vous de bien suivre les

instructions dans cette notice pour réduire au minimum

le risque d’incendie, d’explosion ou la production de

monoxyde de carbone pouvant causer des dommages

matériels, des blessures ou la mort. Le tecnicien agréé

est responsable de l’installation de cette trousse.

L’installation n’est pas adéquate ni complète tant que

le bon fonctionnement de l’appareil converti n’a pas été

vérifié selon les instructions du fabricant fournies avec

la trousse. Le fournisseur de service qualifié ayant

réalisé l'installation assume les responsabilités liées à

la conversion.

NATURAL GAS TO PROPANE GAS CONVERSION

Summary of Contents for BarcelonaLights36ZEN









































Search results

Summary of Contents for BarcelonaLights36ZEN

Reviews:

Related manuals for BarcelonaLights36ZEN

Brands by name

Popular brands

IHP BarcelonaLights36ZEN, Installation And Operation Instructions Manual

Search results

Summary of Contents for BarcelonaLights36ZEN

Reviews:

Related manuals for BarcelonaLights36ZEN

Brands by name

Popular brands