background image

IHP.us.com

900861-00NC

18

Step 7: Remove the (3) screws from the “bottom end” of 

the burner pan area.  The bottom end part fills the space 

between the burner pan and the fireplace side panel.  It is 

held into place with three (3) screws. See 

Figure 23

First remove the two inside screws, then the screw secur-

ing the side wall.  Lift up the area where the two screws 

were and push down where the single screw was, then lift 

the bottom end out of the fireplace.

Step 8: With bottom end removed, wire part, Cat. No. 

F3499 (LED Wire Harness) female connectors to the LED 

male connectors protruding through the wire grommets. 

The male end of the LED connector will lock into the female 

connector in one direction only.  Once locked in position, 

screw the threaded cap of the female connector securely 

to the male connector. 

NOTE:  If you are only using one set 

of LED lights the other female connector of Cat. No. F3499 

will not be used. See Figure 24.

Step 9:  After connecting the LED lights into the LED Wire 

Harness insert the 12-volt adaptor (1/4” terminals) into the 

(red and black wires) of LED wire harness.  Plug the 12-

volt adaptor into the 120VAC GFCI box with weather proof 

cover. 

Bottom End

1. Remove Screws

2. Lift up

3. Push down

V+

LED Lights

Male

Female 

Female

Male 

LED Lights

From 

Fireplace

Inside Fireplace 

LED Light Connection

12-volt adaptor;

 6-foot long

Cat. No. F3481

24-inch LED Wire Harness, 

Cat. No. F3499

10-foot LED Controller Wire 

Harness, Cat. No. F3500

Connects to RGB Control Assembly 

(dimmer and switches)

Female 

Male 

Female 

Male 

Male

Female

Figure 23 - Removing bottom end

Figure 24 - LED Wire Connection

LED LIGHTING INSTALLATION

Continued

Summary of Contents for BarcelonaLights36ZEN









































Reviews: