iHealth BP3 User Manual Download Page 4

facing up and position the cuff 1/2"(1-2cm)above the elbow joint.

c. Tighten the cuff by pulling it towards your body, securing it closed with the

Velcro fastener.

d. While seated, place your hand, palm-side up, in front of you on a flat

surface such as a desk or table. Position the monitor in the middle of your

arm so that it is aligned with your middle finger.

e. The cuff should fit comfortably, yet snugly around your left arm. You

should be able to insert one finger between your arm and the cuff.

Remember to:

1. Make sure that the appropriate cuff size is used; refer to the cuff circumference range in the Specifications section of this

manual.

2. Stay still during measurement. Do not move your arm, body or the monitor.

3. Stay still and calm for one to one and half minutes before taking a blood pressure measurement. Prolonged over-inflation of

the bladder may cause bruises of your arm.

4. Keep the cuff clean. Cleaning the cuff after every 200 measurements is recommended. If the cuff becomes dirty, remove it

from the monitor and clean it with a moistened cloth. Do not rinse the monitor or cuff with running water.

Press the “

” button at any time to interrupt a measurement.

Note:

Physical activity, eating, drinking, smoking, excitement, stress, and many other factors influence blood pressure results.

For answers to frequently asked questions, please visit www.ihealthlabs.com

OPERATION INSTRUCTIONS

• Tap “Start” in your app to start measurement. For detailed operating instructions, please visiting : http:

//www.iHealthLabs.com

Note: Please consult a health care professional for interpretation of blood pressure

measurements.

SPECIFICATIONS

1. Product name: Wireless Blood Pressure Monitor

2. Model: BP3L

3. Classification: Internally powered; Type BF applied part; IPX0, No AP or APG; Continuous operation

4. Machine size: approx. 4.53”×4.53”×2.62”(115mm×115mm×66.5mm)

5. Cuff circumference:

8-21/32” to 14-3/16”(22cm-36cm)

6. Weight: approx. 8.47oz (240g) (exclusive cuff);

7. Power: DC:5.0V

1A, Battery: 1*3.7V

Li-ion 2200mAh

8. Measurement range:

Cuff pressure: 0-300 mmHg

Systolic: 60-260 mmHg

Diastolic: 40-199 mmHg

Pulse rate: 40-180 beats/minute

9. Accuracy:

Pressure: ±3 mmHg

Pulse rate: ±5%

10. Wireless communication:

Bluetooth Low Energy

Summary of Contents for BP3













Reviews: