IEMCA KID 80 IV Touch Instruction Manual Download Page 22 | Manualshive

Page: 22 / 122

background image

EN

2 - INFORMATION FOR USE

KID 80 SIV

2 - Pag. 8 / 71

2.6

OPERATOR PARAMETERS: OPERATION MODE

These parameters are needed for the bar feeder automatic cycle programming and should be
set according to the working requirements as well as to the lathe type that is connected to the
bar feeder. Some parameters concern the working phase, while others are used for the bar
change phase.

WARNING - CAUTION

The parameters are set to a default value (preset value): the bar feeder

performs the automatic cycle according to these values. Some parameters may

not be appropriate for the lathe type or the type of machining requested.

The main operation modes are listed hereunder:

- Accessing the parameters
- Parameter

display

- Parameter

modification

- Subparameter

display

- Subparameter

modification

- Exiting the parameters

«
...
20
21
22
23
24
...
»

Summary of Contents for KID 80 IV Touch



























































































































Reviews:

No comments

Related manuals for KID 80 IV Touch

Brand: C.M.O Pages: 10

Brand: DB Industries Pages: 60

Brand: vc999 Pages: 55

Brand: Salsbury Industries Pages: 4

Brand: Pari Pages: 11

Brand: Pari Pages: 2

Brand: Haas Pages: 5

Brand: Tascam Pages: 78

MINISTUDIO CREATOR US-42

Brand: Tascam Pages: 11

Sonorex Super RK 31

Brand: BANDELIN Pages: 21

BTL7-A/E501-M Series

Brand: Balluff Pages: 194

Brand: B.Pro Pages: 48

Brand: ABB Pages: 16

Brand: ABB Pages: 2

Novation Launchkey Mini

Brand: Focusrite Audio Engineering Pages: 36

Brand: Vitax Pages: 12

Brand: GAPOSA Pages: 32

Brand: ABB Pages: 112

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands