IEMCA KID 80 IV Touch Instruction Manual Download Page 82

Page: 82 / 122

2 - INFORMATION FOR USE

KID 80 SIV

2 - Pag. 68 / 71

16 - AXIAL DISPLACEMENT NOT LOCKED (S1221 Off)

Warning: THE AXIAL DISPLACEMENT SENSOR IS NOT ACTIVE.

CAUSE SOLUTION

Warning
Axial displacement not locked
(S1221Off)

The axial displacement device is
not locked.

Lock the axial displacement device.

The sensor is faulty.

Replace the sensor.

Incorrect reading of the sensor.

Check the distance between the sensor
and the relevant cam.

17 - MOTOR THERMAL CIRCUIT BREAKERS (E11.7)

A MOTOR THERMAL CIRCUIT BREAKER HAS TRIPPED.

CAUSE SOLUTION

Warning
Motor thermal circuit breakers

The oil pump overheating has
occurred.

Make sure that the involved motor can
run freely and check the correct thermal
calibration (according to the amperage).

Check the motor input voltage.

Summary of Contents for KID 80 IV Touch



























































































































Search results

Summary of Contents for KID 80 IV Touch

Reviews:

Related manuals for KID 80 IV Touch

Brands by name

Popular brands

IEMCA KID 80 IV Touch, Instruction Manual

Search results

Summary of Contents for KID 80 IV Touch

Reviews:

Related manuals for KID 80 IV Touch

Brands by name

Popular brands