IEMCA KID 80 IV Touch Instruction Manual Download Page 84

Page: 84 / 122

2 - INFORMATION FOR USE

KID 80 SIV

2 - Pag. 70 / 71

24 - THREAD SAFETY

Warning: THE LATHE HAS NOT CARRIED OUT THE THREADING OPERATION ON THE PIECE TO
BE MACHINED.

CAUSE SOLUTION

Warning
Thread safety

Threading device failure.

Check the effective functioning of the
lathe device.

Threading controlling device failure.

Check the microswitch placed on the
cam box of the thread safety.

The bar did not move to the last
"COLLET OPENING".

Make sure that the lathe collet opens
correctly and check the bar feeder
thrust (parameter 34).

25 - CARRY OUT THE 0-AXIS AFTER A POWER OFF-ON

THE ENCODER VALUE PRESET OPERATION WAS NOT CARRIED OUT CORRECTLY IN THE PRESET
TIME.

CAUSE SOLUTION

Warning
25 Carry out the 0-
axis after a power off-on

The PLC and drive connection
cable is broken.

Contact Iemca service department.

The drive is faulty.

Summary of Contents for KID 80 IV Touch



























































































































Search results

Summary of Contents for KID 80 IV Touch

Reviews:

Related manuals for KID 80 IV Touch

Brands by name

Popular brands

IEMCA KID 80 IV Touch, Instruction Manual

Search results

Summary of Contents for KID 80 IV Touch

Reviews:

Related manuals for KID 80 IV Touch

Brands by name

Popular brands