background image

 

 

28

4.7 

Advanced CMOS Setup 

This section allows you to configure your system for basic operation.    You have 
the opportunity to select the system’s default speed, boot-up sequence, 
keyboard operation, shadowing and security. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

Quick Boot 

When this option is set to enable, DRAM testing function will be disable.

 

 

1st /2nd /3rd Boot Device 

This option sets the type of device for the first boot drives that the AMIBIOS   
attempts to boot from after AMIBIOS POST completes. The settings are 
Disabled, IDE-0, IDE-1, IDE-2, IDE-3, Floppy, ARMD-FDD, ARMD-HDD, 
CDROM, SCSI.

   

 

Try Other Boot Devices 

The options are Yes or No. Set this setting to Yes to instruct AMIBIOS to 
attempt to boot from any other drive in the system if it cannot find a boot 
drive among the drives specified in the 1st Boot Device, 2nd Boot Device, 
3rd Boot Device, 4th Boot Device options. 

 

Boot From LAN 

When setting Enable, bios will load LAN’s Boot Rom and try to boot the 
system from LAN. 

 

S.M.A.R.T. for Hard Disks 

S.M.A.R.T. stands for Self-Monitoring, Analysis and Reporting Technology. 
This setting can help BIOS to warn the user of the possible device failure and 
let the user back up the device before actual failure happens. The options are 
Disabled, Enabled.   

Summary of Contents for WAFER-C400EV














































Reviews: