IEI Technology PAC-400AI-C236 User Manual Download Page 79

Page: 79 / 110

PAC-400AI-C236 Embedded System

Page 69

5.4.2.2 SATA Configuration

Use the

SATA Configuration

menu (

BIOS Menu 24

) to change and/or set the

configuration of the SATA devices installed in the system.

Advanced Chipset

SATA Controller(s)

[Enabled]

SATA Mode Selection

[AHCI]

mSATA

Empty

Hot Plug

[Disabled]

SATA1

Empty

Hot Plug

[Disabled]

SATA2

Empty

Hot Plug

[Disabled]

Enable or disable SATA

Device.

---------------------



: Select Screen

↑

↓

: Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F2: Previous Values

F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

BIOS Menu 24: SATA

Configuration



SATA Controller(s) [Enabled]

Use the

SATA Controller(s)

option to configure the SATA controller(s).



Enabled

EFAULT

Enables the on-board SATA controller(s).



Disabled

Disables the on-board SATA controller(s).



SATA Mode Selection [AHCI]

Use the

SATA Mode Selection

option to determine how the SATA devices operate.



AHCI

EFAULT

Configures SATA devices as AHCI device.



RAID

Configures SATA devices as RAID device.

Summary of Contents for PAC-400AI-C236















































































































Search results

Summary of Contents for PAC-400AI-C236

Reviews:

Related manuals for PAC-400AI-C236

Brands by name

Popular brands

IEI Technology PAC-400AI-C236, User Manual

Search results

Summary of Contents for PAC-400AI-C236

Reviews:

Related manuals for PAC-400AI-C236

Brands by name

Popular brands