IEI Technology PAC-400AI-C236 User Manual Download Page 36

Page: 36 / 110

PAC-400AI-C236 Embedded System

Page 26

3.7 Power-On Procedure

3.7.1 Installation Checklist

WARNING:

Make sure a power supply with the correct input voltage is being fed into
the system. Incorrect voltages applied to the system may cause damage to
the internal electronic components and may also cause injury to the user.

To power on the embedded system please make sure of the following:



The rear surface panel is installed



All peripheral devices (monitor, serial communications devices etc.) are

connected



The system is securely mounted

3.7.2 Power-on Procedure

To power-on the PAC-400AI-C236 please follow the steps below:

Step 1:

Connect the power source to the power inlet of the PAC-400AI-C236 through the

included power cord.

Step 2:

Press the power button to turn on the system. The power LED on the front panel

will turn on in green.

Step 0:

Summary of Contents for PAC-400AI-C236















































































































Search results

Summary of Contents for PAC-400AI-C236

Reviews:

Related manuals for PAC-400AI-C236

Brands by name

Popular brands

IEI Technology PAC-400AI-C236, User Manual

Search results

Summary of Contents for PAC-400AI-C236

Reviews:

Related manuals for PAC-400AI-C236

Brands by name

Popular brands