IEI Technology PAC-400AI-C236 User Manual Download Page 12

Page: 12 / 110

PAC-400AI-C236 Embedded System

Page 2

1.1 Overview

Figure 1-1: PAC-400AI-C236 Series

The PAC-400AI-C236 embedded system is powered by the Intel

Xeon

E3-1275 v5

processor. It is designed for harsh environment applications, and supports wall mounting
method.

The PAC-400AI-C236 provides one PCIe x16 slot and one PCIe x4 slot for building AI
applications by installing IEI Mustang accelerator cards. Its I/O interfaces include two USB
3.2 Gen 1 ports, two USB 2.0 ports, two GbE, and one VGA.

1.2 Model Variations

The model variations of the PAC-400AI-C236 series are listed below.

Model No.

CPU

Pre-installed Memory

PAC-400AI-C236-25

N/A

PAC-400AI-C236-XE/16G/25 Intel

Xeon

E3-1275 v5

16 GB DDR4

Table 1-1: PAC-400AI-C236 Model Variations

Summary of Contents for PAC-400AI-C236















































































































Search results

Summary of Contents for PAC-400AI-C236

Reviews:

Related manuals for PAC-400AI-C236

Brands by name

Popular brands

IEI Technology PAC-400AI-C236, User Manual

Search results

Summary of Contents for PAC-400AI-C236

Reviews:

Related manuals for PAC-400AI-C236

Brands by name

Popular brands