IEI Technology IQ7-DB-MITX User Manual Download Page 101

Page: 101 / 139

IQ7 Design Guide

Page 89

Thermal Mode

The fan adjusts its speed using these

settings:

TargetTemp

Value

Tolerance

Value

Startup

Value

Stop

Value

StopTime

Value

Manual Mode

EFAULT

The fan spins at the set speed, max speed is

at 255, full-off is at 0.

TargetTemp [030]

WARNING:

CPU failure can result if this value is set too high

The fan will turn off if the temperature falls below this value.

Minimum Value: 0°C

Maximum Value: 127°C

Tolerance Value [05]

This options sets how fine the jumps in fan speed are. If the setting is low, the fan will

change speed in small increments, if the value is larger it will change speed in big

amounts.

Min:

Max:

Summary of Contents for IQ7-DB-MITX












































































































































Search results

Summary of Contents for IQ7-DB-MITX

Reviews:

Related manuals for IQ7-DB-MITX

Brands by name

Popular brands

IEI Technology IQ7-DB-MITX, User Manual

Search results

Summary of Contents for IQ7-DB-MITX

Reviews:

Related manuals for IQ7-DB-MITX

Brands by name

Popular brands