IEI Technology IQ7-DB-MITX User Manual Download Page 106

Page: 106 / 139

IQ7 Design Guide

Page 94

6.3.6.1 ME Subsystem Configuration

Use the

ME Subsystem Configuration

menu (BIOS Menu 11) to configure the Intel®

Management Engine (ME) configuration options.

BIOS SETUP UTILITY

Main

Advanced

PCIPNP

Boot

Security

Chipset

Exit

ME Subsystem Configuration

⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯

BootBlock HECI Message

[Disabled]

HECI Message

[Disabled]

End of Post S5 HECI Message

[Disabled]

ME HECI Configuration
ME-HECI [Enabled]
ME-IDER [Disabled]
ME-KT

[Disabled]

Options

Disabled
Enabled

ÅÆ

Select

Screen

↑

↓

Select

Item

Enter Go to SubScreen
F1 General

Help

F10

Save and Exit

ESC Exit

BIOS Menu 11: ME Subsystem Configuration

BootBlock HECI Message

Use the

BootBlock HECI Message

option to enable or disable boot disk sector that

contains the Intel® AMT Host-Embedded Controller Interface (HECI) message.

Disabled D

EFAULT

Boot sector disabled

Enabled

Boot sector enabled

HECI Message [Enabled]

Use the

HECI Message

option to enable or disable the Intel® AMT Host-Embedded

Controller Interface (HECI) message.

Disabled D

EFAULT

HECI message disabled

Enabled

HECI message enabled

Summary of Contents for IQ7-DB-MITX












































































































































Search results

Summary of Contents for IQ7-DB-MITX

Reviews:

Brands by name

Popular brands

IEI Technology IQ7-DB-MITX, User Manual

Search results

Summary of Contents for IQ7-DB-MITX

Reviews:

Brands by name

Popular brands