IEI Technology IQ7-DB-MITX User Manual Download Page 96

Page: 96 / 139

IQ7 Design Guide

Page 84

32Bit Data Transfer [Enabled]

Use the

32Bit Data Transfer

BIOS option to enables or disable 32-bit data transfers.

Disabled

Prevents the BIOS from using 32-bit data transfers.

Enabled D

EFAULT

Allows BIOS to use 32-bit data transfers on supported

hard disk drives.

6.3.3 Super IO Configuration

Use the

Super IO Configuration

menu (BIOS

6) to set or change the

configurations for the FDD controllers, parallel ports and serial ports.

BIOS SETUP UTILITY

Main

Advanced

PCIPNP

Boot

Security

Chipset

Exit

Configure Super I/O Chipset

⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯

Serial Port1 Address

[3F8]

RS-485 Control for SP1

[Disabled]

Serial Port2 Address

[2F8]

RS-485 Control for SP1

[Disabled]

Serial Port3 Address

[3E8]

Serial Port4 Address

[2E8]

Parallel Port Address

[378]

Parallel Port Mode

[Normal]

Parallel Port IRQ

[IRQ7]

Allows BIOS to select
Serial Port Base
Addresses

ÅÆ

Select

Screen

↑

↓

Select

Item

Enter Go to SubScreen
F1 General

Help

F10

Save and Exit

ESC Exit

BIOS Menu 6: Super IO Configuration

Serial Port1 Address [3F8]

Use the

Serial Port1 Address

option to select the Serial Port 1 base address.

Disabled

No base address is assigned to Serial Port 1

3F8 D

EFAULT

I/O port address is 3F8

3E8

I/O port address is 3E8

2E8

I/O port address is 2E8

Summary of Contents for IQ7-DB-MITX












































































































































Search results

Summary of Contents for IQ7-DB-MITX

Reviews:

Related manuals for IQ7-DB-MITX

Brands by name

Popular brands

IEI Technology IQ7-DB-MITX, User Manual

Search results

Summary of Contents for IQ7-DB-MITX

Reviews:

Related manuals for IQ7-DB-MITX

Brands by name

Popular brands