IEI Technology IQ7-DB-MITX User Manual Download Page 110

Page: 110 / 139

IQ7 Design Guide

Page 98

Disabled

The console is not redirected after POST

Boot Loader

Redirection is active during POST and during Boot

Loader

Always D

EFAULT

Redirection is always active (Some OSes may not

work if set to Always)

Terminal Type [ANSI]

Use the

Terminal Type

BIOS option to specify the remote terminal type.

ANSI D

EFAULT

The target terminal type is ANSI

VT100

The target terminal type is VT100

VT-UTF8

The target terminal type is VT-UTF8

6.3.8 USB Configuration

Use the

USB Configuration

menu (BIOS Menu 13) to read USB configuration information

and configure the USB settings.

BIOS SETUP UTILITY

Main

Advanced

PCIPNP

Boot

Security

Chipset

Exit

USB Configuration

⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯

Module Version – 2.24.3-13.4

USB Devices Enabled:
1 Keyboard, 1 Mouse

USB Function

[Enabled]

USB 2.0 Controller

[Enabled]

Legacy USB Support

[Enabled]

USB 2.0 Controller Mode

[HiSpeed]

> USB Mass Storage Device Configuration

Options

Disabled
8 USB Ports
Enabled

ÅÆ

Select

Screen

↑

↓

Select

Item

Enter Go to SubScreen
F1 General

Help

F10

Save and Exit

ESC Exit

BIOS Menu 13: USB Configuration

Summary of Contents for IQ7-DB-MITX












































































































































Search results

Summary of Contents for IQ7-DB-MITX

Reviews:

Brands by name

Popular brands

IEI Technology IQ7-DB-MITX, User Manual

Search results

Summary of Contents for IQ7-DB-MITX

Reviews:

Brands by name

Popular brands