IDTECK iMDC-MAIN User Manual Download Page 55

Page: 55 / 79

p.49

iMDC SEARCH

Select Device

select the device to transmit firmware

Device IP

Input device’s IP to transmit firmware

Device Port

Set IP port to transmit firmware.

Default setting is 6001 for iMDC-MAIN and 6005 for iMDC-RIM.

Code

Description

[Select Firmware!!!]: This button is to open window to transmit firmware.

Select the firmware you want to update.

[Start Transmission!!!]: This button is to send firmware to the device (iMDC-MAIN or i

MDC-RIM). If you stop in the middle of transmitting process, you should restart from #2

step.

If you want to stop transmitting, click the [Stop Transmission!!!] button. Even though t

ransmitting is stopped, any problem doesn’t occur.

iMDC SEARCH

[Search iMDC-MAIN!!!]: This button is to search all existing iMDC-MAIN network infor

Summary of Contents for iMDC-MAIN
















































































Search results

Summary of Contents for iMDC-MAIN

Reviews:

Related manuals for iMDC-MAIN

Brands by name

Popular brands

IDTECK iMDC-MAIN, User Manual

Search results

Summary of Contents for iMDC-MAIN

Reviews:

Related manuals for iMDC-MAIN

Brands by name

Popular brands