IDTECK iMDC-MAIN User Manual Download Page 60

Page: 60 / 79

iMDC EMULATOR

p.54

Mac Address

It’s Mac address of Ethernet card

iMDC-RIM IP

It’s IP address of searched iMDC-RIM board.

iMDC-RIM G/W

It’s gateway address of searched iMDC-RIM board.

iMDC-RIM DNS

It’s DNS address of searched iMDC-RIM board.

iMDC-RIM PORT

It’s port address of searched iMDC-RIM board.

It is used to communicate between iMDC-RIM board and iMDC-MAIN. Usi

ng default (6005) is recommended.

iMDC-MAIN IP

It’s IP address of iMDC-MAIN to connect iMDC-RIM board.

iMDC INFOMATION

Description

If you want to change the iMDC-RIM’s network setting, change the network setting in ‘i

MDC-RIM INFORMATION and click the [Download Information!!!] button to complete.

6.2

iMDC-RIM TEST

Input the iMDC-RIM IP address and port you want to search.

[Change Test Mode!!!]: This button is to change the applicable iMDC-RIM (192.168.10.

31) board to Test Mode.

If the ‘Env Setting Ack!!!’ message appears. It means iMDC-RIM (192.168.10.31) is set a

Summary of Contents for iMDC-MAIN
















































































Search results

Summary of Contents for iMDC-MAIN

Reviews:

Related manuals for iMDC-MAIN

Brands by name

Popular brands

IDTECK iMDC-MAIN, User Manual

Search results

Summary of Contents for iMDC-MAIN

Reviews:

Related manuals for iMDC-MAIN

Brands by name

Popular brands