IDTECK iMDC-MAIN User Manual Download Page 40 | Manualshive

Page: 40 / 79

background image

WIRING

p.34

How to operate

The Wiegand wire of reader is being connected to reader #1, and then if LED control wire is

connected as figure above, LED color is changed from Red to Green.

9.4

READER LED/BUZZER CONTROLLING IN POWER FAIL SAFE MODE

Power Fail Safe Mode

In this mode, if power is failed or emergencies occurs, the door is opened automatically.

In this mode, security level can be lowered because all of the doors are opened automaticall

y but people inside can exit.

How to Indicate Door Opening Status Using LED of Reader in Power Fail Safe

If you connect the LED control wire of the reader to Relay output connected with door lock,

Door lock operation is indicated with LED.

«
...
38
39
40
41
42
...
»

Summary of Contents for iMDC-MAIN
















































































Reviews:

No comments

Related manuals for iMDC-MAIN

Brand: Canarm Pages: 3

Brand: Ebyte Pages: 38

Brand: EBS Pages: 30

Brand: Jands Pages: 7

coviva Smartbox TKP100A

Brand: hager Pages: 34

Brand: Jäger Pages: 50

Brand: Magellan Pages: 2

Brand: OMC Pages: 18

Brand: Paradox Pages: 2

Brand: Paradox Pages: 2

FrameSaver 9120

Brand: Paradyne Pages: 20

VeriSafe VS2-NET

Brand: Panduit Pages: 6

Brand: PAC Pages: 9

Brand: ZIMMERLI MESSTECHNIK Pages: 12

Brand: Newport Pages: 417

Brand: Parker Pages: 38

Brand: Parker Pages: 2

Brand: Cardin Elettronica Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands