background image

Page 12 of 12 

0900885 Rev: REL (02/06) 

DISCLAIMER 

Knight LLC does not accept responsibility for the mishandling, misuse, or non-performance of the described items 
when used for purposes other than those specified in the instructions. For hazardous materials information consult 
label, MSDS, or Knight LLC. Knight products are not for use in potentially explosive environments. Any use of our 
equipment in such an environment is at the risk of the user, Knight does not accept any liability in such 
circumstances. 

WARRANTY 

All Knight controls and pump systems are warranted against defects in material and workmanship for a period of 
ONE year. All electronic control boards have a TWO year warranty. Warranty applies only to the replacement or 
repair of such parts when returned to factory with a Knight Return Authorization (KRA) number, freight prepaid, and 
found to be defective upon factory authorized inspection. Bearings and pump seals or rubber and synthetic rubber 
parts such as “O” rings, diaphragms, squeeze tubing, and gaskets are considered expendable and are not covered 
under warranty. Warranty does not cover liability resulting from performance of this equipment nor the labor to 
replace this equipment. Product abuse or misuse voids warranty. 

World Headquarters 

20531 Crescent Bay Drive 

Lake Forest, CA 92630 

Tel: 949.595.4800 

Fax: 949.595.4801 

www.knightequip.com

USA Toll Free 

Tel: 800.854.3764 

Fax: 800.752.9518 

Canada 

Tel: 905.542.2333 

Fax: 905.542.1536

Australia 

Tel: 61.2.9725.2588 

Fax: 61.2.9725.2025 

UK 

Tel: 44.1293.615.570 

Fax: 44.1293.615.585

North Europe 

Tel: 31.53.428.5800 

Fax: 31.53.428.5809 

South Europe 

Tel: 34.93.487.1015 

Fax: 34.93.215.2019

North Asia Pacific 

Tel: 82.2.3481.6683 

Fax: 82.2.3482.5742 

Southeast Asia 

Tel: 65.9170.0984 

Fax: 65.6489.6723 

KNIGHT LLC,   

A Unit of IDEX Corporation 

Summary of Contents for Knight ILCS EDGE













Reviews: