To stop the alarm cycle, press again the LOCKING push-button of the remote control.
This function always depends from the vehicle (the lock command repetition) where the alarm is installed.
U
U
l
l
t
t
r
r
a
a
s
s
o
o
n
n
i
i
c
c
s
s
e
e
n
n
s
s
o
o
r
r
e
e
x
x
c
c
l
l
u
u
s
s
i
i
o
o
n
n
Alarm armed, during the neutral time (10 seconds), push again the lock button of the original remote control, this operation, signalled by 3 beep, excludes
the ultrasonic sensor.
This function always depends from the vehicle (the lock command repetition) where the alarm is installed.
S
S
t
t
a
a
t
t
u
u
s
s
m
m
e
e
m
m
o
o
r
r
y
y
If during the armed state, the alarm is turned off using the mechanical key or the alarm is detached from the cable harness, after restoration it will
remember the state in which it was. This prevents any tampering attempt.
S
S
e
e
n
n
s
s
o
o
r
r
a
a
d
d
j
j
u
u
s
s
t
t
m
m
e
e
n
n
t
t
Shock sensor sensitivity
Ultrasonic
The shock sensor is factory-tuned to
prevent false alarms. In the event that
sensitivity adjustment is required, rotate
the trimmer, clockwise to increase the
sensitivity, or anti-clockwise to decrease it.
Adjustment shock sensor
+
_
Ultrasonic sensitivity may be adjusted by using
the trimmer in the module. Rotate the trimmer
clockwise to increase sensitivity and anti
clockwise to decrease it. Warning: an incorrect
adjustment may cause false triggering of the
alarm.
Ultrasonic adjustment
HPS 55
E
E
c
c
x
x
l
l
u
u
s
s
i
i
o
o
n
n
o
o
f
f
t
t
h
h
e
e
s
s
i
i
r
r
e
e
n
n
Through the ignition key it is possible to exclude the functioning of the horn or the siren.
With the alarm disarmed (CDL opened), turn on and off the ignition key for 3 times and, within 30 second, press the original remote control to close the
CDL of the vehicle.
From this moment, the central unit will signal the attempt to break in by the flashing of the blinkers only.
A
A
l
l
a
a
r
r
m
m
m
m
e
e
m
m
o
o
r
r
y
y
If the central unit records one or more causes of alarm, they are signalled, when disarming, through the LED. To verify the type of alarm, check the number
of flashings of the LED with the table below.
Flashings
Cause
Flashings
Cause
1
DOOR OPENING
(
SIGNALLED BY CAN
-
BUS
)
6
SHOCK SENSOR
2
CENTRAL DOOR LOCKING
(
SIGNALLED BY CAN
-
BUS
)
7
ULTRASONIC SENSOR
3
BONNET OPENING
(
SIGNALLED BY CAN
-
BUS
)
8
EXTRA SENSORS ALARM
(
BLUE WIRE INPUT
)
4
TRUNK OPENING
(
SIGNALLED BY CAN
-
BUS
)
9
EXTRA SENSORS ALARM
(
BLUE
/
RED WIRE INPUT
)
5
IGNITION ATTEMPT
V
V
a
a
l
l
e
e
t
t
f
f
u
u
n
n
c
c
t
t
i
i
o
o
n
n
This function puts the alarm into stand-by mode. This allows the car to be left at a service centre without leaving the remote control.
Activation of the Valet function:
Compose, using the ignition key, the unlocking code (factory
setting 1-2-3)
If the operation is successful, the LED on the dashboard will flash
twice
Deactivation of the Valet function:
Compose using the ignition key the unlocking code (factory setting
1-2-3)
If the operation is successful, the Led will flash twice and all the
system functions will be restored.
To remind that the Valet function is active the LED on the dashboard will flash twice at any time one turns on the ignition key.
U
U
s
s
e
e
o
o
f
f
p
p
i
i
n
n
c
c
o
o
d
d
e
e
f
f
o
o
r
r
r
r
e
e
l
l
e
e
a
a
s
s
e
e
To be used when the remote controls are lost or no longer operating when the alarm system is still armed.
The code is always made of 3 digits (factory setting: 1-2-3). This code should be composed (when the alarm is armed) via the ignition key as per the procedure detailed below:
1.
Turn the ignition key ON/OFF as many time as per the first digit (e.g. 1 in case of factory setting)
The LED is illuminated while composing the pin code and the horn or the siren sounds.
Wait until the LED extinguishes.
2.
Turn the ignition key ON/OFF as many time as per the second digit (e.g. 2 in case of factory setting)
3.
Wait until the LED extinguishes.
4.
Turn the ignition key ON/OFF as many time as per the third digit (e.g. 3 in case of factory setting)
If you succeed, the alarm system will disarm after the third digit.
M
M
o
o
d
d
i
i
f
f
i
i
c
c
a
a
t
t
i
i
o
o
n
n
o
o
f
f
t
t
h
h
e
e
r
r
e
e
l
l
e
e
a
a
s
s
e
e
p
p
i
i
n
n
c
c
o
o
d
d
e
e
You may customise the factory pre-set release pin code (1-2-3) just following the herewith procedure, alarm disarmed:
1.
Through the ignition key compose the old secret code as described in the previous paragraph.
2.
Wait for quick beeps of confirmation that the old code of unblocking is correct.
Wait until the Led extinguishes.
3.
Turn the ignition key ON/OFF as many times as per the first value to be modified.
The LED will illuminate during the composition of the secret code.
Wait that the LED on the dashboard extinguishes.
4.
Turn the ignition key ON/OFF as many times as per the second value to be modified.
Wait that the LED on the dashboard extinguishes.
5.
Turn the ignition key ON/OFF as many times as per the third value to be modified.
Wait that the LED on the dashboard extinguishes
If you succeed, the quick flashing of the LED on the dashboard confirms that the new secret code has successfully substituted the old one.
THE
NEW
PIN
CODE
WAS
STORED
AND
HAS
SUBSTITUITE
THE
OLD
ONE
INSERT
HERE
THE
NEW
PIN
CODE
M
M
a
a
n
n
u
u
a
a
l
l
P
P
r
r
o
o
g
g
r
r
a
a
m
m
m
m
i
i
n
n
g
g
It is possible to perform some programming moving the internal JUMPER.
HPS 841 rev. 03 - 03-2010 pag. 4 of 30
COD
:
HPS421
