Download catalogs and CAD from http://asia.idec.com/downloads
E-078
APEM
Switches &
Pilot Lights
Control Boxes
Emergency
Stop Switches
Enabling
Switches
Safety Products
Explosion Proof
Terminal Blocks
Relays & Sockets
Circuit
Protectors
Power Supplies
LED Illumination
Controllers
Operator
Interfaces
Sensors
AUTO-ID
Saf
ety
P
ro
du
cts
Interlock
Switches
Non-contact
Interlock Switches
Safety Laser
Scanners
Safety Light
Curtains
Safety Modules
HS6B
HS6E
HS5D
HS5L
HS1L
Actuators for
HS1/HS5/HS6
Actuators/
Padlock Hasp
HS5 Series Door Handle Actuator
5. Install the switch cover unit on the mounting frame and panel.
Mounting screws or nuts are not supplied and must be provided by
the user.
Installing the rear unlocking button
When the total thickness of mounting panel is 3.0 mm or less: Install
the rear unlocking button on the rod on the back of the switch. For
details, see the instruction sheet for the HS5E-
L/HS5E-K
L/
HS5L-
L.
When the total thickness of mounting frame or panel is 20 mm or
more: Install the rear unlocking button kit (HS9Z-FL5
) sold
separately. For installation, see the instruction sheet for the HS9Z-
FL5
.
Installing the Handle Unit HS9Z-DH5RH
1. Install the front handle (black) on the shaft on the actuator cover as
shown below.
2. Tighten Screw D attached to the handle
using a hexagonal wrench (size: 2.5).
Apply Loctite to the screw so that it does not
become loose.
3. Install the handle unit on the mounting frame
and panel, aligning the handle unit and
switch cover unit as illustrated under
“Actuator Mounting Reference Position.”
Mounting screws and nuts are not supplied
and must be provided by the user.
4. Cut the rear handle shaft according to the thickness of the mounting
frame and panel.
Cut at
→
Cut at
→
Cut at
→
Cut at
→
Cut at
→
Cut at
→
No cut
→
1
2
3
4
5
6
Mounting panel
thickness (X)
0 < X ≤ 10mm:
10 < X ≤ 20mm:
20 < X ≤ 30mm:
30 < X ≤ 40mm:
40 < X ≤ 50mm:
50 < X ≤ 60mm:
60 < X ≤ 70mm:
5. Align the rear handle plate, rear handle shaft, and the rear handle
base as shown below, and fasten them using two Screws E. Apply
Loctite to the screws so that they do not become loose.
Shaft Positioning Pin
Rear Handle Base
Screw E
Screw E
Rear Handle
Plate
Rear Handle
Shaft
6. Install the rear handle (gunmetal color) on the rear
handle shaft.
7. Tighten Screw D attached to the handle using a hexagonal wrench
(size: 2.5). Apply Loctite to the screw so that it does not become
loose.
Screw D
8. Turn the handle to the locked position, and insert the rear handle
shaft into the actuator cover. The rear handle should be in the locked
position.
9. While adjusting to ensure smooth
operation of the rear handle,
fasten the rear handle unit on the
mounting frame and panel.
*
Install the HS9Z-DH5LH in a similar
fashion as the HS9Z-DH5RH. Note that
the handle direction becomes opposite.
*
Mounting screws and nuts are not
supplied and must be provided by the
user.
Actuator Mounting Reference Position
• The mounting reference position and allowable mounting range are
as shown below.
0.8
3
Reference Position
• Use the square dot pattern as a guide of the allowable mounting
range.
Reference
Position
4
2
7 to 9
LOCK
UNLOCK
4
2
LOCK
UNLOCK
All dimensions in mm.
Installing the Rear Unlocking Button Kit
1. Install the connecting rod onto the
push rod on the HS5E/HS5E-K/HS5L rear
unlocking button model (HS5E-
L/HS5E-
K
L/HS5L-
L) rear unlocking button
interlock switch.
2. A pin is attached to the connecting rod.
Using pliers, press the pin into the hole in
the push rod.
3. Pull out the connecting rod from the hole in the mounting frame, and
turn the button operating pin to the horizontal position.
Correct
Incorrect
Connecting Rod Orientation
Pull
Connecting Rod
Pin
Mounting holes required
in the frame. See panel cut-out.
Mounting Screws
Nuts
Handle Position
Locked
Unlocked
Shaft
Screw D
Mounting
Screws
Nuts
Unlocked
Mounting
Screws
Nuts
Locked
HS5E-
L
Interlock Switch
Pin
Connecting
Rod
Push Rod
Instructions
