background image

2

Harrier GTE - 

Installation & Servicing

GENERAL

Note.

Fuel rates and flue gas data relate to maximum output ratings.
Gas firing data relates to the use of NATURAL GAS ONLY.

Details for the use of LPG are available on request from Caradon
Ideal Ltd.

Natural gas consumption is calculated using a calorific value of
38.7MJ/m

3

 (1038Btu/ft

3

) gross or 34.9MJ/m

3

 (935Btu/ft

3

) nett at

15ºC and 1013.25mbar.

Oil rates relate to Gas Oil using a calorific value of 45.56 MJ/kg
gross or 42.69 MJ/kg nett.

Table 1 Performance Data

Boiler

GTE 5

GTE 6

GTE 7

GTE 8

GTE 9

Number of Sections

5

6

7

8

9

Maximum

kW

140

180

230

280

330

Heat Output

Btu/hx10

3

478

614

785

955

1126

Minimum

kW

105

140

180

230

280

Heat Output

Btu/hx10

3

358

478

614

785

955

Hydraulic

mbar

20.3

37.9

55.8

82.7

118.6

Resistance at 11k

in w.g.

8.1

15.2

22.3

33.1

47.5

Hydraulic

mbar

6.1

11.5

16.9

25.0

35.9

Resistance at 20k

in w.g.

2.5

4.6

6.8

10.0

14.4

Combustion Chamber

mbar

0.6

1.1

1.6

2.2

2.5

Resistance (at zero draught)

in w.g.

0.24

0.44

0.64

0.88

1.0

Minimum Draught at Smokehood mbar

0

0

0

0

    0

Outlet (for max. output)

in w.g.

0

0

0

0

    0

HEALTH & SAFETY DOCUMENT NO. 635

The electricity at work regulations, 1989.  The manufacturer's
notes must NOT be taken, in any way, as overriding statutory
obligations.

IMPORTANT. These appliances are CE certified for safety and
performance.  It is, therefore, important that no external control
devices, e.g. flue dampers, economisers etc., are directly
connected to these appliances unless covered by these
Installation and Servicing Instructions or as otherwise
recommended by Caradon Ideal Limited in writing.  If in doubt
please enquire.

Any direct connection of a control device not approved by
Caradon Ideal Limited could invalidate the certification and the
normal appliance warranty.  It could also infringe the Gas Safety
Regulations and the above regulations.

Maximum

l/h

15.52

19.76

25.10

30.66

35.81

Oil Rate

gal/h

3.41

4.35

5.52

6.75

7.88

Maximum Flue

m

3

/s

0.090

0.114

0.145

0.178

0.208

Gas Volume

ft

3

/min

191

242

308

376

440

Flue Gas CO

2

 / Temperature

% / ºC

13 / 210

13 / 210

13 / 210

13 / 210

13 / 210

Oil

Table 2 General Data

Flow Connection

in./DN

R2

1

/

2

 / 65

R2

1

/

2

 / 65

R2

1

/

2

 / 65

R2

1

/

2

 / 65

R2

1

/

2

 / 65

Return Connection

in./DN

R2

1

/

2

 / 65

R2

1

/

2

 / 65

R2

1

/

2

 / 65

R2

1

/

2

 / 65

R2

1

/

2

 / 65

Drain Connection

in

R1

1

/

2

R1

1

/

2

R1

1

/

2

R1

1

/

2

R1

1

/

2

Safety Valve & Expansion

in

R1

1

/

2

R1

1

/

2

R1

1

/

2

R1

1

/

2

R1

1

/

2

Maximum Operating Pressure

bar

6

6

6

6

6

Boiler  Thermostat  Setting

ºC

30 - 90

30 - 90

30 - 90

30 - 90

30 - 90

Safety Thermostat Setting

ºC

110

110

110

110

110

High / Low Setting

ºC

30 - 90

30 - 90

30 - 90

30 - 90

30 - 90

Nominal Flue

m m

180

180

200

200

200

Diameter

in.

7

7

8

8

8

Boiler Water

l

116

136

156

176

196

Content

gal

25.5

29.9

34.3

38.7

43.1

Boiler DRY Weight

kg

608

694

791

886

977

less Burner Unit

lb

1340

1530

1744

1953

2154

Maximum

m

3

/h

16.13

20.56

26.09

31.87

37.23

Gas Rate

ft

3

/h

569

726

921

1125

1315

Maximum Flue

m

3

/s

0.092

0.117

0.149

0.182

0.213

Gas Volume

ft

3

/min

196

249

316

386

452

Flue Gas CO

2

 / Temperature

% / ºC

9.5 / 210

9.5 / 210

9.5 / 210

9.5 / 210

9.5 / 210

Gas

Summary of Contents for GTE 5













































Reviews: