manualshive.com logo in svg

IDEAL Networks NaviTEK NT, User Manual

Share
Download
IDEAL Networks NaviTEK NT User Manual Download Page 5

 

 

 

NaviTEK NT 

 

153800 Iss 1 

User Guide 

 

Page 5 

Power 

NaviTEK NT can be powered from: 

•

 

A rechargeable power module, 

•

 

Directly from power connected to the DC inlet built in to the power module. 

•

 

From an alkaline battery pack. 

The type of module or pack supplied as standard depends on the model purchased. 

 

Power Module Management 

A fully charged  power module will support up to five  hours of heavy,  continuous use.  For 

maximum life of the power module it is recommended to discharge it fully and then recharge 

it fully at least once a month. 

The power module is not user-serviceable.  When it has reached the end of its life, contact 

your local IDEAL representative for service. 

Power Module Recharging 

The power module can be fully recharged in three hours with the NaviTEK NT switched ON or 

OFF.  To recharge the power module, connect the supplied power adaptor to the DC inlet.  

For convenience the power module may be removed from, or left attached to, the tester for 

charging. The Power LED next to the DC inlet glows green to show that the battery is being 

charged, and flashes green to show that it is not being charged.  The power module’s charge 

state is indicated at FULL, 2/3, 1/3 and EMPTY by the graphical power meter shown  in the 

information bar at the top of the display. 

 

 

Fig 1  Power indications 

Battery Pack 

The battery pack accepts four replaceable AA alkaline cells.  These cells cannot be recharged. 

 

 

Summary of Contents for NaviTEK NT































Reviews:

No comments

Brands by name

Popular brands

Load more brands