manualshive.com logo in svg

IDEAL Networks NaviTEK NT, User Manual

Share
Download
IDEAL Networks NaviTEK NT User Manual Download Page 11

 

 

 

NaviTEK NT 

 

153800 Iss 1 

User Guide 

 

Page 11 

NOTES 

If the NaviTEK NT is connected to an active network when it is switched ON, it will 

automatically detect the network and display its IP address in the HOME screen. 

If the NaviTEK NT is not connected to an active network when it is switched ON, it will 

automatically enter Cable mode and run a Wiremap test. 

If the NaviTEK NT is connected to an active network after it is switched ON, press the soft 

key DETECT (F1) to detect the network. 

 

Setup 

All user-defined settings and preferences of the NaviTEK NT are set from the SETUP menu.   

 

 

 

 

 

 

Fig 8 

 

Setup menu descriptions 

From the Cable or Ethernet  home screen, 

press the soft key SETUP (F3) to display the 

Setup menu . 

Selecting any of the icons will produce the 

options that follow: 

 

Fig 9 

 

ABOUT 

UPDATE 

PREF 

LANG 

FACTORY 

IPv4 

IPv6 

RJ45 

SETUP 

SYSTEM 

Summary of Contents for NaviTEK NT































Reviews:

No comments

Brands by name

Popular brands

Load more brands