manualshive.com logo in svg

ICT CRX-POSTX-DIN, Installation Manual, Page: 7 / 68

Share
Download
ICT CRX-POSTX-DIN Installation Manual Download Page 7

CRX-POSTX-DIN 

DIN Rail PostX IP Reporting Module 

Installation Manual | June 2017   

7

 

 

1.2

 

PostX Module Editions 

There are four editions of the PostX module. All editions enable you to program up to 4 communication 
channels for reporting messages from the connected alarm panel. The communication interface of each channel 
can be configured independently, allowing you to select from Ethernet, PSTN, WiFi or GPRS, according to the 
module used.   

 

 

Communication Interface 

 

Ethernet 

PSTN 

WiFi 

GPRS 

CRX-POSTX-DIN 
PostX DIN Rail IP Reporting Module 

 

 

 

 

CRX-POST-DIN-WF   
PostX DIN Rail IP Reporting Module with WiFi 

 

 

 

 

CRX-POSTX-DIN-GP 
PostX DIN Rail IP Reporting Module with GPRS 

 

 

 

 

CRX-POSTX-DIN-WFGP 
PostX DIN Rail IP Reporting Module with WiFi and GPRS 

 

 

 

 

 

The features specific to modules with a WiFi and/or GPRS interface described in this manual are only relevant if 
you are using the appropriate edition. 

 

Summary of Contents for CRX-POSTX-DIN





































































Reviews:

No comments