manualshive.com logo in svg

ICT CRX-POSTX-DIN, Installation Manual, Page: 38 / 68

Share
Download
ICT CRX-POSTX-DIN Installation Manual Download Page 38

38

 

CRX-POSTX-DIN 

DIN Rail PostX IP Reporting Module 

Installation Manual | June 2017 

 

 

11.3

 

Confirm IP Address via Command Line 

Ping is an application that runs in Microsoft Windows and is a very useful tool for helping to diagnose an IP 
address related issue. It can be used to test a connection with the PostX Module. The following instructions 
detail how to ping a device: 

1.

 

Open a command prompt (Click Start->Run, then type "cmd" into this window and click "OK"). 

2.

 

Type 

ping

 

192.168.1.2

 into the command prompt and press ENTER. 

3.

 

Wait for the command prompt to respond. The first of the images below shows a ping attempt where the IP 
address was not found. The second image shows a successful ping attempt where the IP address was 
found. 

 

Console screenshot of a Ping where the IP address cannot be found 

 

Console screenshot of a Successful Ping 

 

Summary of Contents for CRX-POSTX-DIN





































































Reviews:

No comments