manualshive.com logo in svg

ICT 1500W Sine Wave Series, Instruction Manual

Share
Download
ICT 1500W Sine Wave Series Instruction Manual Download Page 3

 

Innovative Circuit Technology Ltd.

 

3 

Contents 

 
INTRODUCTION ................................................................................. 4 

INSTALLATION ................................................................................... 4 

OPERATION ........................................................................................ 8 

Status Indicators and Alarms......................................................... 9 

AC Transfer Switch ...................................................................... 10 

TCP/IP WEB-BASED UTILITY OPTION ............................................... 11 

Status and Control ....................................................................... 12 

Device Setup ................................................................................ 13 

Network setup ............................................................................. 14 

E-mail Setup................................................................................. 17 

User Setup ................................................................................... 18 

Maintenance ............................................................................... 19 

MOBILE WEB APP ............................................................................ 20 

PASSWORD and IP ADDRESS RESET ................................................ 21 

ROUTER CONFIGURATION ............................................................... 22 

TEXT MESSAGE ALARM NOTIFICATIONS ......................................... 24 

TROUBLESHOOTING ........................................................................ 24 

PRODUCT SPECIFICATIONS .............................................................. 25 

LIMITED WARRANTY........................................................................ 28 

 

 
 
 
 
 
 
 

Summary of Contents for 1500W Sine Wave Series





























Reviews:

No comments

Brands by name

Popular brands

Load more brands