manualshive.com logo in svg

ICT 1500W Sine Wave Series, Instruction Manual

Share
Download
ICT 1500W Sine Wave Series Instruction Manual Download Page 4

4 

Innovative Circuit Technology Ltd. 

INTRODUCTION 

The ICT1500 Sine Wave Series is a compact high efficiency true sine wave output 
DC to AC inverter with features optimized for commercial applications. 

•

 

Unparalleled power density at 1500W, with 3000W surge capability 

•

 

115Vac 60Hz and 230Vac 50Hz models, with 93% peak efficiency 

•

 

Includes TCP/IP Ethernet port with built in web-server, and support for 
SNMP v1/v2 management systems for remote control and monitoring 

•

 

Includes automatic transfer switch with user definable trip levels 

•

 

Includes convenient front AC outlet(s) and/or hardwired rear AC terminal 
block 

•

 

Form C alarm contacts for remote notification of alarms 

•

 

Low EMI, FCC Class A compliance 

•

 

Temperature controlled variable speed fan for low noise and long life 

•

 

Optional 19" dual inverter rack mounting for installing 2 units side by side 
in a 1.5U rack space 

•

 

Optional DC wiring box for code compliant standalone installations 

 
Model Numbers: 
 

115Vac 60Hz Models 

230Vac 50Hz Models

1

 

Battery Voltage 

ICT1500-12SWTC 
ICT1500-24SWTC 
ICT1500-48SWTC 

ICT1500A-12SWTC 
ICT1500A-24SWTC 
ICT1500A-48SWTC 

12 
24 
48 

 
Optional Accessories: 
 
19

” 

Rack Mount Tray (mount up to 2 inverters): 

ICT-RM2U 

Wiring Junction Box (attaches to back of inverter): 

ICT-DCWB 

 

INSTALLATION 

Installation must only be done by technical personnel familiar with local electrical 
authority wiring requirements. 
 
Perform a quick physical check of the unit as it is being taken out of the box to 
ensure it has not been damaged during shipping. Check for the included parts and 
accessories shipped with your unit: 

•

 

3 pin Form-C alarm connector plug 

•

 

Wall mounting bracket, with mounting screws (4), installed 

•

 

Instruction Manual 

•

 

Bus bar (with 5/16 inch holes) hardware: 1/4 inch bolt, nut, and washer 
set (2) 

 

1

 These models have the rear terminal block only. 

Add suffix “/AUS” to the model 

numbers for a single 

front AU1-10P and rear terminal block. 

Summary of Contents for 1500W Sine Wave Series





























Reviews:

No comments

Brands by name

Popular brands

Load more brands