manualshive.com logo in svg

ICT 1500W Sine Wave Series, Instruction Manual

Share
Download
ICT 1500W Sine Wave Series Instruction Manual Download Page 24

24 

Innovative Circuit Technology Ltd. 

TEXT MESSAGE ALARM NOTIFICATIONS 

The inverter can send alarm notifications as text messages to a cell phone by 
configuring the alarm e-mails to be sent to your mobile phone service provider. 
On the 

E-mail Setup

 page of the web-based utility, enter the text address of your 

phone in the 

Recipient E-mail Addresses

 field.  

 
Example with an AT&T phone: enter the recipient address 

cellnumber

@txt.att.net

, 

replacing 

cellnumber

 with your 10 digit cell phone number. 

 
Cell address formats for some common North American mobile phone providers: 
 

AT&T 

 

 

cellnumber

@txt.att.net 

Verizon   

 

cellnumber

@vtext.com 

Sprint   

 

cellnumber

@messaging.sprintpcs.com 

T-Mobile 

 

cellnumber

@tmomail.net 

Virgin Mobile 

 

cellnumber

@vmobl.com 

Nextel   

 

cellnumber

@messaging.nextel.com 

Bell Mobility 

 

cellnumber

@txt.bell.ca 

Rogers   

 

cellnumber

@pcs.rogers.com 

Telus 

 

 

cellnumber

@msg.telus.com 

Virgin Mobile (Can) 

cellnumber

@vmobile.ca 

 

TROUBLESHOOTING 

 

I am unable to access the web-based configuration utility. 

 

•

 

Check that you are using the correct IP address for the inverter by running 
the IP Address Discovery Utility (available on the Tools download section 
of the ICT Web page 

http://www.ict-power.com/tools-utilities/

 ) to locate 

the connected inverter and see the assigned IP address. Run the utility on 
a Windows computer connected to the same network as the inverter, and 
it will report the IP addresses of all ICT units connected to that network. 
The IP address may have been changed if DHCP is enabled. 

 

•

 

Ensure you are using an industry standard “crossover” type of network 

cable if directly connecting a computer to the inverter

, and a “straight

-

throu

gh” type of

 cable to connect the inverter to a network. 

 

•

 

Ensure the network card settings on your computer are configured for 
accessing the IP address of the inverter. To access a unit with the default 
IP address of 192.168.0.180 the typical network settings for your 
computer are: 

o

 

IP Address: 192.168.0.180 

o

 

Subnet Mask: 255.255.255.0 

o

 

Gateway: 192.168.0.1 

Summary of Contents for 1500W Sine Wave Series





























Reviews:

No comments

Brands by name

Popular brands

Load more brands