12
LIMITED WARRANTY
The Manufacturer warrants only that the product shall meet its specifications: this warranty is in lieu of all other written or unwritten, expressed or implied warranties and The Manu-
facturer expressly disclaims any warranty of merchantability, or fitness for a particular purpose. The buyer assumes all risks whatsoever as to the use of the material. Buyer’s exclusive
remedy as to any breach of warranty, negligence or other claim shall be limited to the replacement of the material. Failure to strictly adhere to any recommended procedures shall
release the Manufacturer of all liability with respect to the materials of the use thereof. User of this product must determine suitability for any particular purpose, including, but not
limited to, structural requirements, performance specifications and application requirements prior to installation and after product has been properly applied.
CYLINDER WARRANTY
TO MAINTAIN WARRANTY, DO NOT MAKE ANY CHANGES OR ADJUSTMENTS TO THE CYLINDER OR CYLINDER COMPONENTS, INCLUDING PLUMBING. ICP Group warrants
that the cylinder is fit to dispense ICP’s foam products that are loaded into the cylinder by ICP Group. OTHER THAN THAT WARRANTY, ICP MAKES NO OTHER EXPRESS OR IM-
PLIED WARRANTIES AND ICP SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF MECHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. The sole remedy for any breach of warranty is replacement of the cylinder. ICP Group IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. The terms,
conditions and warranties applicable to ICP dispensed from the cylinder are covered in other ICP documentation relating to that purchase. Buyer must not make any changes to the
cylinder or the cylinder components, including plumbing. Any such change may produce dangerous results and cause damage or injury, including a loss of product stored in the cyl-
inder. ICP Group is not responsible for damages or injuries resulting from any such changes. Those damages or injuries are Buyer’s responsibility, and ICP Group may charge Buyer
for the costs of any resulting cylinder damage or repairs. ICP Group also reserves the right to restrict future sales if the Buyer does not address safety concerns such as modified or
missing plumbing, pressure relief valve activated or excessive cylinder pressure.
CHEMICAL SPILLS
• If liquid spills from the A-component cylinder, provide ventilation and isolate the area. Wearing protective equipment, soak up the spill with an oil absorbent material such as
vermiculite or sawdust. Place the material in an open container. Do not seal the container. Allow the loosely covered container to stand for several days before disposing in accor-
dance with all applicable federal, state and local regulations consistent with good industrial practice.
• Decontaminate the waste and spill area with a solution of 0.2-0.5% liquid detergent and 3-8% concentrated ammonium hydroxide in 90-95% water (5-10% sodium bicarbonate
or baking soda may be substituted for bleach). Use 10 parts of solution for each part of spill and allow the decontaminating solution to react for several hours.
• If liquid spills from the B-component cylinder, soak up the spill with oil absorbent material and dispose of in accordance with all applicable federal, state and local regulations.
Wash the spill area thoroughly with soap and water.
• Consult Safety Data Sheet (SDS), for accidental release measures and disposal considerations. In case of transportation emergency 24 hour day, contact CHEMTREC 1
800.424.9300.
IN CASE OF FIRE
• Responder must wear full emergency equipment including self-contained breathing apparatus.
• Use dry chemical, carbon dioxide, foam or large amounts of water spray (do not use direct spray) to control fire.
• Use water spray to cool exposed containers and reduce risk of rupture.
WARNINGS
Polyset
®
adhesive products are composed of a diisocyanate, blowing agent and polyol. Consult the product’s SDS (available at www.polysetadhesives.com) for specific information.
The urethane foam adhesive produced from these ingredients will support combustion and may present a fire hazard if exposed to a fire or excessive heat about 240°F (116°C). Wear
protective glasses with side shields or goggles, nitrile gloves, and clothing that protects against dermal exposure. Recommend using in a well ventilated area with certified respiratory
protection or a powered air purifying respirator (PAPR). For more information regarding a certified respiratory program please visit http://www.cdc.gov/niosh/. To view or receive
a copy of ICP Building Solution Group’s respirator program, please contact ICP Building Solution Group Customer Care at 800-321-5585. Personal Protective Equipment can be
purchased through ICP Building Solution Group’s distribution by purchasing the Polyset
®
Contractor Safety Kit (F65251). The Contractor Safety Kit includes: nitrile gloves, contractor
safety glasses, and a NIOSH approved negative pressure half mask respirator. FOR PROFESSIONAL USE ONLY. WARNING: Non-Flammable Compressed Gas. Keep away from heat.
Smoking and open flames, including hot work, should be prohibited in the vicinity of a foaming operation. Avoid contact with skin and eyes. May cause sensitiza- tion by inhalation
and/or direct skin contact. Avoid prolonged or repeated breathing of vapor. KEEP OUT OF REACH OF CHILDREN. FIRST AID: In any first aid case CONSULT A PHYSICIAN. EYES:
Flush with water for at least 15 minutes. SKIN: Remove contaminated clothing. Wash skin with plenty of soap and water. Cured adhesive must be removed manually. INHALATION: If
breathing is difficult, give oxygen. If breathing has stopped, give artificial respiration. INGESTION: give large quantities of water. Do NOT induce vomiting. Contact a physician imme-
diately in any first aid situation. Consult the product’s SDS (available at www.polysetadhesives.com) for specific information.
IMPORTANT
Always read all operating, application and safety instructions before using any products from ICP Building Solutions Group. Use in conformance with all local, state and federal
regulations and safety requirements. Failure to strictly adhere to any recommended procedures and reasonable safety precautions shall release ICP Building Solutions Group of all
liability with respect to the materials or the use thereof. For additional information and location of your nearest distributor, call ICP Building Solutions Group 330-753-4585.
NOTE:
Physical properties shown are typical and are to serve only as a guide for engineering design. Results are obtained from specimens under ideal conditions and may vary upon
use, temperature and ambient conditions. Right to change physical properties as a result of technical progress is reserved. This information supersedes all previously published data.
Yields shown are optimum and will vary slightly depending on ambient conditions and particular application. Read all product directions and safety information before use. This prod-
uct is organic, and therefore, is combustible. Consult local building codes for specific requirements regarding the use of cellular plastics or urethane foam in construction.
Polyset
®
Foam Adhesive products are composed of a diisocyanate, hydrofluorocarbon blowing agent and polyol. Consult the product’s SDS (available at www.polysetadhesives.
com) for specific information. The urethane foam adhesive produced from these ingredients will support combustion and may present a fire hazard if exposed to a fire or excessive
heat about 240°F (116°C). Wear protective glasses with side shields or goggles, nitrile gloves, and clothing that protects against dermal exposure. Recommend dispensing product in
a well-ventilated area with certified respiratory protection; however, well ventilated exterior applications may not need respiratory protection. It is the responsibility of the employer
to complete a PPE evaluation and/or exposure assessment to determine if respiratory protection is required. Read all instructions, ICP Product Stewardship Guidelines, and SDS
(Section 8) prior to use of any product.
FOR PROFESSIONAL USE ONLY.
