08
iCool Sport
STEP 6
Now that you have preset your desired temperature and started the
circulating pump, notice that the pump button will have changed from
start to stop. You can use this same button to start and stop the pump at
any time. Now, touch the start system button and the cooling cycle will
begin. The water will be cooled to your pre-set temperature and the
system will then cycle to maintain it at that temperature automatically.
The system can only be started once within any 3 minute period to
avoid overloading the compressor. So if you don’t hear it start when
you touch the start system button, do not touch the again, the iCool
will start automatically after the 3 minutes safety period elapses.
For the safety of users, you can not set temperatures below 5°C or
above 45°C. (40°F-112°F) In an emergency you can stop all functions
immediately by touching the “all stop” button however, if the cabinet is
hot, only the fan may continue to run until the cabinet has cooled.
To change from cooling to heating or back you must restart.
The system on the left hand side can also heat and will automatically
enter into either the cooling or the heating mode depending on your
first temperature setting. It heats and cools by modern heat pump
technology using as much less electricity. The right hand side is for
cooling only, it does not heat.
Setting up to use the Heating Mode
For safety reasons you can only initiate the heating mode at the time
the unit is first switched on. You can not change to heating while you
are using it in the cooling mode or vice versa. You must switch off at the
main switch and start again to change modes.
Your iCool selects either cooling or heating automatically
For example, if you set the temperature to a value that is BELOW the
current water temperature in your pool it will automatically begin
COOLING when you touch the START SYSTEM button.
If you set the temperature to a value that is ABOVE the current water
temperature in your pool it will automatically begin HEATING when you
touch the START SYSTEM button. To use the heating function use the
up down arrows to select the hot temperature you require up to 45ºC
(or 108ºF) and then touch the START button. This takes you back to
the main operating screen where you can now start the PUMP and the
SYSTEM as usual. The status bar on the front of the unit will turn RED
when you touch the START button to indicate that your iCool is now
heating. It will continue to heat until it reaches your pre set temperature
and then hold that temperature for as long as you wish.
You must use a pool cover when heating the water
We all understand heat rises, so you must use a cover on top of your
pool when heating it or you will lose a large amount of the heat energy
into the room and it will take much longer to heat the water.
The Loss of Water Flow Warning Screen
If water stops flowing for more than two minutes the iCool will sound
a warning and shut down. This screen will appear.
The Water Flow Warning Screen also provides an option to over ride the
flow protection system in the rare situation of a false alarm.
Once you use this function to disarm the flow safety monitor nothing
will stop the system even if water is not flowing and this can seriously
damage the pump as it will have no lubrication or cooling from the water.
This over ride function is only to be used for short periods where it is
essential to keep your system operating until the reason for the false
alarm can be determined and corrected.
Water flow can also stop if the heat exchanger tank is frozen solid
If you set the temperature below about 7ºC or 45ºF it is occasionally
possible in certain climatic conditions for the heat exchanger tank to
freeze solid which will block the flow of water.
In order to cool the pool water to these extremely low temperatures the
system must cool to at least 5 to 7ºC below the set temperature and
this takes it very close to the temperature that water freezes solid.
Following international safety standards your iCool will not accept water
temperature settings below 5ºC or 40ºF as this would put athletes
using the system unattended at risk of hypothermia. However, the iCool
is easily powerful enough to freeze the water and if this happens the
safety screen above will appear and the system will stop.
WARNING
Never use this option unless you are absolutely certain that the
system has stopped because of a false water flow alarm
Warning Screen
Summary of Contents for TWIN
Page 1: ...Owners Manual iCool TWIN ...
