IC
ON
MO
TO
SP
OR
TS
AI
RF
R
AM
E P
RO
M
AN
UAL
IC
ON
MO
TO
SP
OR
TS
AI
RFR
AM
E PR
O H
ELM
ET
In order for your helmet to function properly, the chinstrap must always be securely fastened while in use. With the chinstrap fastened, it
should not be possible to remove the helmet from your head by pulling up at the center rear. Check periodically to see that the vibration
has not caused the chinstrap to loosen. Just give a little tug to make sure it is still tight.
To securely fasten the D-ring retention system, thread the end of the chinstrap through the D-rings only as shown in the diagram
below. Fasten the female snap of the chinstrap to the male snap to secure the loose end of the chinstrap after the chinstrap is securely
fastened. The only function of the snap fastener on the end of the chinstrap is to keep it from fl apping in the air stream. It is not part of
the retention system and should not be used independently without passing through the D-rings as illustrated below.
To release the D-ring retention system, unsnap the loose end of the chinstrap from its fastener. Then pull on the red fl ag attached to the
end of the lower D-ring to loosen the strap. Once loose, feed the end of the strap back through the D-rings to fully release the chinstrap.
Please make sure that the chinstrap is fastened as instructed above. Failure to do so may result in fatal injury.
2
3
RIGHT CHEEK PAD
LEFT CHEEK PAD
COMFORT LINER
CHIN CURTAIN
XXS
35
mm
XS
30
mm
S
30
mm
M
25
mm
L
30
mm
XL
25
mm
XXL
20
mm
3XL
20
mm
HELMET SHELL SIZE
15
mm
12
mm
15
mm
12
mm
12
mm
9
mm
7
mm
7
mm
1
2
3
1
4
EE5
6
3
2
2
1
1
2
1
PROPER FITTING
CHINSTRAP
2
3
1
5
6
No helmet can protect the user against all foreseeable impacts. For your safety, please choose a helmet in the size that fi ts your head.
For maximum head protection, your helmet must be of proper fi t and the retention system must be securely fastened under the chin.
1. Position the helmet on your head so that it sits low on your forehead. If you can’t see the edge of the brim at the extreme upper range of your
vision, the helmet is probably out of place. Adjust the retention system so that when in use, it will hold the helmet fi rmly in place.
Always
make sure you can see well enough to safely operate your motorcycle
2. With the chinstrap still fastened as tightly as possible, take hold of the helmet with both hands. Without moving your head, try to move
the helmet up and down, and from side to side. You should feel the skin of your head and face being pulled as you try to move the
helmet. If you can move the helmet around easily, it is too big. Try a smaller size.
3. Now, with the chinstrap secured, put your hands fl at on the back of the helmet and try to pull the helmet off by rotating it forward.
Then, put your hands on the front of the helmet, and try to push the helmet off by rotating it toward the rear. If the helmet starts to come
off in either direction, the helmet is either too large, or the chinstrap is not fastened tightly enough.
If helmet comes off, try another size
or another model.
1.
WRAP FLEXIBLE TAPE MEASURE
APPROXIMATELY ONE INCH ABOVE
EYEBROWS AND EARS
2.
USE THIS MEASUREMENT TO FIND
YOUR “INCHES” OR “CENTIMETERS”HEAD
SIZE IN OUR HELMET SIZING CHART
To ensure a proper fit, please follow the steps below:
Helmet fi t is critical to helmet protective performance. Different helmets fi t differently due to differences in design and construction. The
correct helmet size can only be checked and confi rmed by physically fi tting the helmet to the user. Always try the helmet on in a store,
before purchasing it, to be sure you are purchasing the correct sized helmet for you.
SAFETY WARNING: Never buy a used helmet or borrow someone else’s helmet. Over time the protective foam in helmets will adjust to the
contours of a user’s head. A used or borrowed helmet may not offer as much protection as a new helmet.
Wearing the wrong size helmet can
increase your risk of serious injury or death in an accident. A helmet that is too large for your head may be dislodged or knocked off in an
accident. To select the right size helmet for your head, follow these instructions.
CHOOSING THE CORRECT HELMET SIZE
SAFETY WARNING: The helmet size chart below is only for reference. Always try the helmet on and follow this manual’s instruction for proper fi t.
SAFETY WARNING: Do not rely on the snap to secure the helmet. The snap is provided only to prevent the strap from fl apping in the air. Fasten
the retention system only in the following manner of the picture.
1. Wrap fl exible tape measure approximately one inch above eyebrows and ears.
2. Use this measurement to fi nd your “inches” or “centimeters” head size in our helmet sizing chart.