Icom IC-M603 Instruction Manual Download Page 60

Page: 60 / 64

SPECIFICATIONS AND OPTIONS

New2001

■

Specifications

General

• Frequency coverage

: TX 156.000–161.450 MHz

RX 156.000–163.425 MHz

• Mode

: FM (16K0G3E), DSC (16K0G2B)

• Current drain (at 13.8 V)

: TX high (25 W) 5.5 A

Max. audio

1.5 A

• Power supply requirement

: 13.8 V DC (10.8 to 15.6 V)

(negative ground)

• Frequency stability

: ±5 ppm

• Operating temp. range

: –20°C to +60°C

• Antenna impedance

: 50

Ω

nominal

• Input impedance (MIC)

: 2 k

Ω

• Output impedance (audio)

: 4

Ω

• Dimensions : 220(W)

110(H)

109.4(D) mm

(Projections not included)

• Weight : Approx.

1400

Transmitter

• RF output power

: 25 W and 1 W

• Modulation system

: Variable reactance frequency

modulation

• Max. frequency deviation

: ±5.0 kHz

• Spurious emissions

: Less than 0.25 µW

• Adjacent channel power

: More than 70 dB

• Audio harmonic distortion

: Less than 10%

(at 1 kHz, 60% deviation)

• Residual modulation

: More than 40 dB

• Audio frequency response

: +1 to –3 dB of 6 dB/octave

range from 300 Hz to 3000 Hz

Receiver

• Receive system

: Double conversion superheterodyne

• Sensitivity (20 dB SINAD)

: –5 dBµ emf (typical)

–5 dBµ emf (typical)

(CH 70 receiver)

• Squelch sensitivity

: –5 dBµ emf (typical)

• Spurious response

: More than 75 dB

• Intermodulation

: More than 75 dB

• Adjacent channel selectivity : More than 75 dB
• Hum and noise

: More than 45 dB

• Audio output power

: 2.0 W (typical) at 10% distortion

with a 4

Ω

load

All stated specifications are subject to change without
notice or obligation.

!IC-M603.qxd 06.7.28 1:46 PM Page 54 (1,1)

Summary of Contents for IC-M603

































































Search results

Summary of Contents for IC-M603

Reviews:

Related manuals for IC-M603

Brands by name

Popular brands

Icom IC-M603, Instruction Manual

Search results

Summary of Contents for IC-M603

Reviews:

Related manuals for IC-M603

Brands by name

Popular brands