Icom IC-M603 Instruction Manual Download Page 26

Page: 26 / 64

DSC OPERATION

New2001

■

Distress call

A Distress call should be transmitted if, in the opinion of the
Master, the ship or a person is in distress and requires imme-
diate assistance.

NEVER

USE THE DISTRESS CALL WHEN YOUR

SHIP OR A PERSON IS NOT IN AN EMERGENCY.
A DISTRESS CALL CAN BE USED ONLY WHEN
IMMEDIATE HELP IS NEEDED.

Simple call

Confirm no Distress call is being received.

While lifting up the key cover, push

[DISTRESS]

for 5 sec.

to transmit the Distress call.

• Emergency channel (Channel 70) is automatically selected and

the Distress call is transmitted.

• When no GPS is connected, input your position and UTC time, if

possible.

• While pushing

[DISTRESS]

, the key backlighting blinks.

After transmitting the call, the transceiver waits for an ac-
knowledgment call on Channel 70.

• The Distress call is automatically transmitted every 3.5 to 4.5

minutes.

• After 2 sec., the transceiver is set to Channel 16 automatically.

Distress Call

TX Complete

Now Waiting for ACK

<CLR

<CLR˘Cancel>

Cancel>

After 2 sec.

25W

INT

TAG

Wait ACK

<CLR˘

Cancel>

CALLING

Distress Call

Push for 5 sec.

!IC-M603.qxd 06.7.28 1:46 PM Page 20 (1,1)

Summary of Contents for IC-M603

































































Search results

Summary of Contents for IC-M603

Reviews:

Related manuals for IC-M603

Brands by name

Popular brands

Icom IC-M603, Instruction Manual

Search results

Summary of Contents for IC-M603

Reviews:

Related manuals for IC-M603

Brands by name

Popular brands