Icom IC-M220 Instruction Manual Download Page 41

Page: 41 / 66

DIGITAL SELECTIVE CALLING (DSC)

Receiving a Position Request call

(May not be used, depending on the presetting)

NOTE:

Even if the Auto ACK function is set to “Manual,” after receiving a Distress

Acknowledgement, or while in the Distress Cancel call procedure, the Position Reply is

automatically sent to the calling station.

When a Position Request call is received:

•An alarm sounds.

•

“RCVD POS Request” is displayed.

1. Push

ALARM OFF

to turn OFF the alarm.

Push the Software Key below the intended operation.

IGN

(Ignore)

Ignores the call and returns to the

operating screen.

•The call is saved in the DSC Log.

•“ ” blinks continuously until you display

the call message.

ABLE

( Able to

comply)

Sends Acknowledgement “Able to

comply” right away.

UNABLE

(Unable to

Comply)

Sends an Acknowledgement

“Unable to

Comply.”

•The call is saved in the DSC Log.

•

Displays the Acknowledgement

information, and then returns to the

operating screen by pushing

EXIT

ACPT

(Accept)

Accepts the call.

•Displays the received call’s information.

•The call is saved in the DSC Log.

Push

ABLE

UNABLE

, then push

CALL

send the Position Reply call.

(p. 27)

Summary of Contents for IC-M220



































































Search results

Summary of Contents for IC-M220

Reviews:

Related manuals for IC-M220

Brands by name

Popular brands

Icom IC-M220, Instruction Manual

Search results

Summary of Contents for IC-M220

Reviews:

Related manuals for IC-M220

Brands by name

Popular brands